Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 17 , 2026 through Tuesday August 31, 2026. Our experts Saikat Nandy and Prashanth Bargur Hanumantharayappa will be waiting to assist you and resol...
Hello, I have some Cisco 2800 APs (AP2802E) setup as Flex connect with a AIR-CTVM-K9. The problem I'm having is clients are dropping a lot of pings when it roams to a specific AP, CWA09P, I think my client is going through a full roam everytime it c...
Hi Guys,I have Cisco Prime 2.2 and WLC 8.3.122.0 and I added WLC in Cisco prime and is synchronized but no AP are added! what could be the reason?
Hello,Trying to convert an AIR-AP1815I-K9 access point from CAPWAP to ME, installation of a new image fails. IP adress assignement -> OKPinging with tftp server -> OK.tar image download -> reach 100% but stuck there. During the process, console outp...
Hi,I wanted to know if there is any Cisco documentation on a n+1 HA design where I have one vWLC in one DC and the second one in a diff DC geographically different. The vWLC in use will be a 9800-CL. In this scenario the mgmt ip will also be differen...
Dear Community, I need my 3850 switch works as a Wireless Controller but i am facing some problems. I have 2 3850 switches which are deployed on different location on a same office. I have 5 access points and need integrate with the wireless controll...
Hi,We are trying to deploy AIR-CAP3502I-A-K9 with 5508 controller. However the controller is back order and we don't want to delay our site survey. Can we use the AP in stand alone mode for the site survey? We don't need it to operate or pass traffic...
Hello,Since updating to firmware 25.14 on my MR33 ap's, my machines are connecting to access points nowhere near to them, e.g. they can be sat below an access point, less than 2 metres, but connect to another access point across the building with a v...
I found some trouble about Wifi internet cannot print out data but LAN can print.I use access point for CISCO WAP-150 and just update version of firmware to 1.1.1.0 on middle last week. but just found trouble on Monday. and for CORE SWITCH i use CISC...
I have 12AP each transmitting 3 of 4 SSID in a factory in Slovakia that's basically a part of a huge warehouse, our bit is split into four chunks by fire proof walls. There's some offices too at each end. So, anyhoo, it doesn't seem to matter what I ...
Does AIR-AP1832i-B-K9 support Mobility Express features, if yes can I deploy it here in Nigeria. Because am configuring it to function as Mobility Express but immediately I power on the AP, straight out of the box, the CiscoAirProvision SSID was not ...
Hi I have the issue for long time. Does anyone also have the issue? I never have access to WLC and AP by SecureCRT. When I logon to them, I can see some message, but I cannot type any commands. Later I found that Putty can work with WLC and AP. But I...
I have an instance at a Fire Station on Spectrum Cable with 2 buildings, 1 OEAP602 in each building. Both 602's link and function as expected to a common WLC on 8.3.150.0 code. In the process of retiring all 602's with 1815t's supported on a differ...
I'm familiar with using PI/CMX with 3702 APs and Halos for Hyperlocation, but there seems to be no documentation on using 2800 APs and Fastlocate. I'm not sure what positioning info is needed: I expect I will need x/y/z axis positioning within the bu...
Roaming between different networks and groups of APs. Good Morning. What is the best configuration practice on the controller (Cisco 5520) to roaming between different networks (L3) transparently on a network with authentication on a Firewall.
Hello, Can anyone explain to me if you need dhcp option 43 when you have your access point in the same vlan as your controllers management interface?
