Good afternoon! There is a problem connecting Cisco Proximity to VKS terminals. When Cisco Proximity starts, the program starts searching for the terminal but the connection does not occur, although the terminal is nearby, another device is connected...
Forum Posts
I've been tasked with setting up Certificate based authentication on our wireless network. i'm close but am looking for advise from anyone who might have done this or something similar. we have a semi-complex architecture. One primary facility and...
Resolved! cisco wirelless controller Ap problem
Hi Friends I have more Cisco Ap(Air-Cap-2702 E-E-K9 int my company everthing is ok but i have 2 problem1) When some user connect to specialy one AP these users after 2-3 minute disconnect from wifi what is reason? 2.4Ghz and 5GHZ is active . i think...
Hi, I bought 3 1815i APs from my IT distributor and when I tried to set them up for my customer I found that there was 2 versions of this AP, one with a Lightweight firmware which needs a WLC to work and a one with Mobility Express which is autonomou...
estoy reinstalando en windows 10 la aplicación de cisco proximity y me aparece el error 2753.lo que ya hice fue borrar temporales del sistema y del perfil del usuario reiniciando el equipo e intente instalar nuevamente pero me aparece el error 2753 n...
On a Linux Host, we need to access the Signal Strength Levels of WIFI probe frames using a Cisco IW3702-4e-uxk9 firmware 15.3.(3)jd. Does the Driver natively support this, is radiotap supported? What could we do to get access to this RSSI values?Usin...
Hello guys,I am running into a problem in my WLC 9800 CL, I cannot pass multiple VLAN traffic, I have configured the Vswitch as a trunk and activated promiscuous mode. Switch Port Configurationinterface Port-channel15description ** Port-Channel to UC...
Resolved! CAPWAP over CAPWAP
Can I configure APs to work via CAPWAP over another CAPWAP link? I am using point-to-point bridge network as circuit between two buildings and would like to traverse multiple VLANs on switch network and do CAPWAP with APs behind L2 switch. I have at...
Resolved! WiFi6 and cloup apps4
Hello a customer of mine asked me: "why do I need a wifi6 if all of my apps are in the cloud and my Internet bandwidth is 100 Mbps?" Does someone know the answer? Thank you Marcos
hi EverybodySome weeks ago i have been had some issues with some APs and in all case i ve seen the same next message error DTLS_CLIENT_ERROR: ../capwap/base_capwap/dtls/base_capwap_dtls_connection_db.c:2214 Max retransmission count reached for Connec...
Resolved! Checking the access point release date
Hi all,Is there a way I can check the initial release date of the Meraki MR42 access point model?Thanks.
Resolved! Same SSID Separate Networks
Hi All,Our business is built on acquisition and we have multiple businesses to support within our Group. I have created a Group level network within the Dashboard which contains sites from both UK and Ireland. Only now since I have checked in the Iri...
we are trying to accomplish the following: we are running into issue inserting the *OR* and space. has anyone ran into something like this? This is a client request.
Hello!We are just implementing a radiating cable to our cisco AIR-AP2802E-E-K9.We would like to set the antenna A to 2,4 GHz and antenna B to 5 GHz.On my WLC it is not possible, because only combinations of A or A+B or A+B+C or A+B+C+D are possible a...
Hi,Several of our users are unable to access the internet when connecting to one of the SSIDs. I increased the DHCP scope a few weeks ago and there a plenty of leases left. I can't explain why this is happening. I'm clutching at straws at the moment ...
