Hey Community! I'm excited to share something we've been working on that I think will really resonate with many of you managing wireless networks today. We just released the Cisco State of Wireless Report 2026, based on insights from over 6,000 wirel...
Forum Posts
Hi folks, I have an issue with CPI v3.3.0 at the moment where although it is performing a sync with my WLCs the total AP counts are a few hundred off and so I have a bunch of APs which are displayed as being 'Not Associated' with any WLC. This in tur...
I have a Z3 gateway, and an MR33 access point.no matter what settings i put on the SSID of the MR33, my Epson SX535WD printer will not connect properly to the MR33. Yet if I set up an ssid with the same settings on the Z3 it works fine.all other clie...
Resolved! Map Foreign Controller interface to Anchor Controller vs use interfaces defined on Anchor Controller
In Cisco guest WLAN architecture, regardless LWA & CWA variations, have Foreign Controller and Anchor Controller to configure. I'm confused with some configuration variations in terms of guest interfaces used on the Anchor Controller:Scenario 1:Forei...
If an AP is setup as an OEAP, and the ssid in use is set to local switching, will the client still be dropped off at the same physical interface the AP is on? Or... will clients on an OEAP automatically be centrally switched regardless of how the ssi...
Does the 8540 Wireless Controller support any network programmability abilities for configuration and to pull operational state info (ex: Netconf, Restconf, XML, JSON, YANG data models)?
Just replaced 13 1602i's with 1852i-b-k9's. Previous devices were pulling proper 172.22.160.0/22 ip's.only 3 of the 13 acquired proper ip's. of the rest, 3 reported 192.168.0.101 (1 each switch) the rest nothing.Switch's report proper CDP signatur...
Hello, We are running a WLC 5508 and we seem to be having a hard time casting to Apple Devices. Android Devices - no problem. Running Firmware / Software Version 8.3.143.0 Our issue is that Apple products (iPhone) can go through the set-up process ...
Hi, I have a wireless network with 802.1x authentication, contain Cisco Aironet CAP-2702i connected to a controller. Today, i want to configure an autonomous access point for make a bridge between my network 802.1x and my AP. Thank you for your help.
Hello, We have a remote WLC 5520 (fw 8.2.130.0), some 3802E and I APs in flexconnect mode, local switching.On our WS-C3650-48PD switches, we have this configuration for APs ports:interface GigabitEthernet1/0/48description AP PORTswitchport trunk nati...
Fellow colleagues,Where can I find guidance on how to properly configure a single, dual-radio, AP so that the 5GHz is serving clients full time while the XOR radio acts as a full-time sensor? We are using a 3504 WLC and our APs are 2802i. If there is...
Problem: In our end client's environment there is an android TV, which faces intermittent disconnection. This is particular to this device only. When ran debug I am seeing orphan packet being sent by the client. We tried configuring static IP for t...
Hii am looking for some help, i am currently have a situation where my client whats to report and view the mac address for all mobile device with in the company's wireless bubble, connected to an SSID or not (probe request) Does anyone know of a sol...
i have my cisco access point 1130AG ip address assigned by my DHCP but i cannot access the page setting when i enter it on the browser url address. It says page cannot display
I currently have two AIR-CAP3602I-E-K9 that are set up in 'bridge+flex' mode so our users can screencast seamlessly whilst walking between the areas covered by the two access points. We also need coverage in another room which is essentially a farada...
helo all, I am currently installing Cisco wireless IPS (WIPS), which is the WIPS are integrated with Cisco Prime and WLC. The installation already done and i try to prove the feature of WIPS that can prevent Rogue AP. I'am using Honeypot that running...
