Model: Cisco Aironet 2802i AIR-AP2802I-Z-K9 Hello. I'm doing some test on an AP by changing the firmware back and forth repeatedly by "archive download-sw" command. The firmware which I switch back and forth are 8.3.112.0 (ap3g3-k9w8-tar.153-3.JD...
Forum Posts
Resolved! MR45 and SSID not visible on HP laptops
I am in the process of upgrading to the MR45's at the college I work at. I recently discovered that the HP laptops on our campus will not display the SSID. The fix is updating the NIC driver. It seems any driver previous to 2018 does not work. Luckil...
Hi All, Recently purchased AIR-AP2802I-E-K9 but have been unable to update the firmware in preloading stage from 8.5.140.0 to 8.8.125.0. I have attempted this from both tftp web gui and CLi but both fail and each time. The msglog reports :-%CAPWAP-3...
Resolved! MR66 questions
We have an MR66 setup in the gymnasium and I was just curious to ask the community. If I stand close to the AP no matter what I can never connect to it which is odd. There are 2 antennas which I have a picture provided. One is inside and the other is...
Hi there,We are replacing 40 AVAYA Wirelss APs with Meraki MR45 APs; however, the client currently is using Avaya Identity Engines Ignition Server IDE (RADIUS) which performs authentication and identity services. Unfortunately under authenticator det...
Hello. We are running a WLC 5520 with about 800 accesspoints. Accesspoints are 1600, 1852, 2802, 2702 and 1142. We run software version 8.2.130 right now. We have a very strange problem. Android phones connected to the wifi get an error when download...
Hi All,I am planning to cover a Mezzanine area which is 300 feet long and 30 feet wide. My plan is to go for one 2800E with AIR-ANT2566P4W-R. However I have doubts regarding if adding one AP with antenna on wall facing other end of wall should be eno...
I've been working on a Cisco 3802i WLC. I am unable to ping the Management IP address of WLC. - I've followed step-by-step instructions from Cisco, how to configure 3802i WLC. - Configured with proper IP address, subnet mask and gateway IP address. -...
Hi all, I'm doing the initial set up of a 3750G WLC through the web GUI (device manager.) I've come to the login splash page for the WLC itself and it's asking for a username and password. I've tried various combinations of admin/admin (which is what...
Since the "forced" upgrade to MR 25.9 firmware, my ESP8266 devices fail to reconnect to Meraki if they disconnect and connect frequently. These devices can enter deep sleep and connect again every few minutes to update their data. If those periods ar...
On the screen of the phone it is saying: registration in progress it has been doing this for a while and I think I am stuk in a loop. This is my phone 7841, I am trying to get SIP firmware on there through my Tftp server but it seems to be stuk in a ...
Hi,I have 3 APs working on a ME environment, the master AP (wlc) and 2 APs associating to the wlc (all ME capable). All working perfectly.Yesterday i try to add two more APs, but i have noticed something when i was booting boths APs (before i have tr...
I'm a volunteer at our local hospice thrift store, working on electronics, testing and preparing for sale. I've worked a lot with domestic wireless networking, but not the pro stuff. We've had one of these access points donated and I'd like to be abl...
Hellol, I have a new AIR-AP1852I-B-K9 and want to add it to the rest of the APs in cisco wirelss controller 2500.I thought there should be a place in web UI to add mac address and that should do everything else.please help. thanks
Hi All. This is is to ask if you had this issue in order to help me with your experience.I was trying to upgrade CT2504 from 8.2.151.0 to 8.3.150.0 but when the copy is finished, either TFTP o SFTP, by CLI or GUI, fails and ends with this message: "F...
