Resolved! MS225-48LP-HW Poe Availability
Hi All,I have a question regarding the amount of PoE availabilty for the MS225. The data sheet says that it has 370W available across 48 ports but how many ports could acutally be used of 48 ports ?Thanks,Tom
Hi All,I have a question regarding the amount of PoE availabilty for the MS225. The data sheet says that it has 370W available across 48 ports but how many ports could acutally be used of 48 ports ?Thanks,Tom
This is terrible. I had a 5508 WLC that I couldn't access remotely but Prime reported that it was still serving APs. TAC RMA'ed it. Got the replacement, upgraded the code and I could access the GUI. I restored the config from a backup and guess wh...
Hello, The last generation of WLAN controllers integrated in switches had some problems and limitations.Does anyone know whether the 9800 embedded also requires access points to be connected directly to the switch that houses the controller? So far...
Hi Guys, Can anyone help on the Prime infrastructure disk utilisation /var. it prevents NCS application to start. To get NCS application to start manually deleted some small log files, ncs cleanup also done but same 100% in /var.. ade # df -h...
Dear Cisco community,I am a newbbie on Wireless controller implementations and I require to implement a WLC 5508 in a HSRP core switch configuration. I want to implement certain level of redundancy by connecting the WLC 5508 to both core switches.Giv...
Hi I have a WAP321 which has the wireless disables and I have no idea how to enable it, and with my limited tech knowledge am struggling. I cannot see it when attached to my Sky Q router, or when attached to laptop. Any guidance welcome please. T...
Hi I have some troubles with one of my clients on my wireless networks. The session timeout on my WLC is 30min. per default and the clients gets disconnected every 30 min as expected. But this one client takes about 1-2 minutes before i reconnects....
HiI am hoping that you can assistWe have installed a new 5508 WLC into a new buinging and also installed new 200 AP's which are 2802i. These have beenconverted to capwap using AP-type capwap command.On the WLC, not all the AP's are showing up as conn...
I am using local PEAP profile on local WLC and "local net users" associated to it.But scan gun cannot connect:what could be cause of this problem?
Hello,I want to install some AIR-ANT2566P4W-R antennas outdoor against the wall, the 2602e access points will be mounted on the interior side of the wall, altough the wall is 30cm thick, so I need some antenna extension cables.What type of coax exten...
Hello Team, tried registering the access point with the wlc and found that this a Mobility express access point. Is it possible to convert this access point to the capwap controller based access point? even though after conversion, is it possible to ...
Hi all,I have two questions regarding Cisco's list of 'Supported Country Codes': https://www.cisco.com/c/en/us/td/docs/wireless/wcs/3-2/configuration/guide/wcscfg32/wcscod.html 1. How does Cisco set this list? (Does Cisco access some sort of internat...
Hi, I would like to share with you the 2802i Tx Power Chart that I created.I hope it will help you to understand better Power levels of the 2802i Access point. CLI:show advanced 802.11-abgn summaryshow advanced 802.11a txpower Please see attached f...
I'm trying to update software of vWLC (small scale version to 8.3.143.0) Below is the current show sysinfo. (Cisco Controller) >show sysinfo Manufacturer's Name.............................. Cisco Systems Inc.Product Name............................
I've seen a discussion about importing mac addresses into the mac filter db on a cisco controller but is there a way to export the mac filter db? I have a Cisco 5508. Thanks.Robert Quinn
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 11-17-2026 11:43 AM | ||
| 10-15-2026 05:58 PM | ||
| 10-12-2026 06:46 PM | ||
| 09-30-2026 07:34 AM | ||
| 08-10-2026 11:32 AM |
| User | Count |
|---|---|
| 5 | |
| 2 | |
| 2 | |
| 1 | |
| 1 |