Wireless

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

review


Labels

Forum Posts

Hi All,I have a 3702i AP and I cannot get wireless clients to connect to the 5GHz channel no matter what I do. I read a couple postings back in 2014 and 2015 and someone said the autonomous software is for site survey only which means 5GHz cannot be ...

Em87 by • Community Member
  • 7082 Views
  • 14 replies
  • 0 Helpful votes

Hi,   I am trying to integrate my Cisco Prime with ACS. but its not successful. I just followed steps from the below cisco document.- "Use Cisco ACS With RADIUS or TACACS+ for External Authentication" https://www.cisco.com/c/en/us/td/docs/net_mgmt/pr...

I have a Cisco 3502I Access Point that shows as registered in Prime Infrastructure but it is not accepting clients.  I have already deleted it,   added it back,  and it has been rediscovered by the WLC but it still does not accept clients.....  Can s...

Tree1964 by • Visitor
  • 2014 Views
  • 2 replies
  • 0 Helpful votes

Hey all,   After upgrading my WLC 2504 to 8.4.100 i no longer had the 25 licenses that the device shipped with from the factory..   Any idea what happened or what i can do to get them back.  Been running on the temp licenses for a few months until i ...

jkemper01 by • Level 1
  • 3018 Views
  • 9 replies
  • 0 Helpful votes

Hi,I m new to wireless technology and currently we have 2 Critical and 2887 Minor alarms are showing in Cisco Prime.Most of these alarms are relate with the Rogues configuration under Cisco Wireless Controller.Because unclassified 2586 Rogue Aps and ...

image.png
alvinaung by • Frequent Visitor
  • 3055 Views
  • 7 replies
  • 0 Helpful votes

Hi guy’s,I have a problem with one of my access points (AIR-AP1832I-E-K9C).When the access points is booting, the access point going in error.On the console view get I a message from L2 error detection.Means this that there is a problem with de NIC o...

bwm218 by • Community Member
  • 2922 Views
  • 3 replies
  • 0 Helpful votes

Hi Folks,we have been suffering a bit with a subset of Samsung phones which simply shows the against the Wi-Fi No Internet connection. These seem to be recent phones a Note 9 and an A8 (or A9 the remote engineer was vague) running Android 8.1.0 from ...

cta102 by • Level 3
  • 13474 Views
  • 4 replies
  • 0 Helpful votes

Hi, is there any way to count the total number of clients that have ever connected to an SSID?I'd like a webpage with a counter - total number of new clients connected = nSo that every time a new client connects to a specific SSID the counter increme...

nrlwells8 by • Community Member
  • 4386 Views
  • 2 replies
  • 0 Helpful votes

Hello experts,  I am setting up a new vWLAN Controller version 8.0.152.0  with AP1131AG access points.The controller address is 172.16.10.5  the 2811 router is configured asip dhcp pool APnetwork 172.16.10.0 255.255.255.0default-gateway 172.16.10.1op...

Hi , any pointers appreciated.   GE patient monitors (Carescape B450)           -  use broadcast/unicasr from Monitor to Host and back   (GE monitor has static IP and has server IP defined) (units do not support multi c)   GE monitor – network attach...

philip.koch by • Frequent Visitor
  • 970 Views
  • 1 replies
  • 0 Helpful votes
Review Cisco Networking for a $25 gift card