Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Hello, In my Cisco WLC output for persistent interference devices (show ap auto-rf 802.11b "AP Name") Sometimes I see a timestamp for when the device was last active and sometimes I don't see any timestamp. If there is no timestamp does that mean t...
Hello everyone, I have a weird issue with the 2504 controller. I have a primary and backup controller. They are both configured with the same settings (different IP addresses for management interface and 2 other vlans that i have configured) I have...
Hi, Will the release WLC 8.5 on CT3504 be support the AIR-AP 1602i and 1702i ? Thanks
I have an Aironet 1852i, with Mobility Express pre-installed (and confirmed to be in ME mode), and I am trying to configure it with 2 wlans for our internal domain networks (both using Windows RADIUS, and both on seperate vlans with seperate external...
Resolved! Meraki AP uplink IP addressing question
Hello all. Does each Meraki AP require a unique routable IP address? So if you have 4000 APs, you'd require 4,000 unique routable addresses? Secondly, can you configure a private ip on the Meraki AP uplink interface, then static NAT it to a public IP...
Dear All, I have a requirement from client, wherein they would want to have the "usernames" of end hosts that are connected on wifi be reflected in Monitor-> Clients dashboard. The only way this is possible IMO is for the client that are associat...
Hi Guys, Please advise if AIR-AP1832I-E-K9 support Data Roaming, I cant seem to find the information on its data sheet. Regards Tony
Hi, Have simple setup where the wlc uses ISE for Radius for AAA , and get this message %APF-3-CLIENT_NO_ACCESS: Authentication failed for client: 74:8d:08:6a:f1:43. ACL override mismatch from AAA server The authC policy checks wireless MAB and def...
Hi,Do the Cisco Aironet 1540 Series Access Point currently support point-to-point and point-to-multipoint for bridging between LANs in buildings?
Hi When trying to add AP to controller I'm reviewing the following log as the AP is not able to join the controller Below is the results I get with the newer WAPS *Mar 1 00:00:13.011: APAVC: Initial WLAN Buffers Given to System is 2500 *Mar 1 0...
First off not sure what community to post in. Couldn't find a Meraki specific one. I am going to be rolling out over 100 new sites and we are going to go with Merkai. Each site will contain a single MX, two MSs, and two MRs (5 devices total per loca...
Hello, Data rates enabled can be changed at 2 different locations in WLC, I didn't find information if any priority : RF profiles vs 802.11b/g/n global parameters. - All 802.11b data rates (actually all behind 12 Mbps) have been disabled in global pa...
I am trying to install the vWLC in VMware. However, I get the following error information. Starting portmap daemon....starting usc cd installation scriptifconfig: SIOCGIFFLAGS: No such deviceifconfig: SIOCGIFFLAGS: No such devicelooking for cdrom de...
Hi Everyone ! I have an issue with Cisco 1832i AP. I already set the SSID for my AP. PCs and Mobile Phones also connected to my AP and could access the internet. But, when I tried to access the AP's IP address for manage some config, I can't login t...
Dear Support team. I am using Cisco Aironet 1200 series. Now I hava a new device want to addition into Cisco system. But I can not do because there is a different point. For detail, let see the picture is attacked and explain me how to change them.
