Hi, We have recently configured a SSID using 802.1X and 802.11r is enabled. Upon looking at all the connection logs and keeping an eye on the Wireless Health , I have been able to observe that we are now having lots of events of that type :auth_mode=...
Forum Posts
Hello Team, We have a design of Multiple anchors to multiple foreign, Foreign and anchor WLCs are in different Mobility groups. All foreign WLCs are in the same Mobility groups. Anchors-WLC1 and Anchors-WLC2 are in the same Mobility groups. Anchors...
Hi All, We accidentally used the C9800-40 17.12.5.bin file on C9800-CL model in Install mode. While the package got created, the upgrade failed for obvious reasons. We copied the right image once we realised our mistake, but now it doesn't let us cre...
Hello Cisco WLAN-Experts,we will soon run out of users on our two 9800-L-C-Guest-WLCs crossing the border of 5000 concurrent users:-------------------------------------------Wlan-name ID Client count -----------------------------...
Hello, i have been trying to compose a report of clients connecting to the 2.4 ghz Wifi via the event log, i have been able to get the 802.11 association but that is pulling the 5 ghz as well, I'd rather not have to scroll through thousands of entrie...
Resolved! C-ANT9103 with C9130e
Can I use this antenna with 5GHz?Is 802.3bt required?I want to install it for a warehouse at one end, replacing ANT2566P4W-RS= I have RF devices 1x1 stream Please, I would appreciate your answer
What are the differences between types of Client IP assignments for SSIDs? Meraki DHCP, Local LAN and L3 Roaming...
Hi everyone, I'm currently facing an issue with the Embedded Wireless Controller (EWC) running on Catalyst 9115AX Access Points. We're using MAC filtering across all WLANs (SSIDs) to control access to the wireless network. Each device’s MAC address (...
hello everyonethese days i am experiencing a problem due to Redirect ACL failure message,below i am releasing the details of my EWLCEWLC firmware 17.6.4I checked via wireshark the response received from cisco ise and indeed the connection is accepted...
Hello, I tried to launch a job on my Cisco Prime (current version is 3.8.1) to archive the configuration of my Cisco 9800 WLC, but the job gave me the "Partial Success status". Either the Running and the startup configs are successful, but the "Fetch...
Resolved! C9800-L-C-K9 無線コントローラのポート設定について
こんにちわ。 C9800-L-C-K9無線コントローラにおいて、 ファイアウォールのようなポート設定ってあるのでしょうか？ 例えばコントローラ上でTCP80を開放したいんです。 となった場合の設定方法を教えてください！！ ドキュメントやGUIの設定画面を探してもどうしてもわからなくて。 よろしくお願いいたします。（そもそも無線でポート遮断という概念があるのか？）
Hi guys! Hope you all good!I had issues while deletion of users in the user management portal some days back. I keep deleting users which are expired. Recently when i deleted users in bulk, the valid users got deleted (nearly hundred users). I select...
Customer had some update done on Aeroscout and since then NMSP is inactive Controllers: 2 5508 in HA mode running 8.5.140 MSE 3355 running 8.0 Prime version 3.4 Verified the Auth list. readded the Hask Key shown in MSE. in the debug it shows handsha...
I need to know what the access points' joining procedures are in SSO deployments and N+1 deployments, and what the timers are in each section. For example, in SSO, if the primary controller fails, what will happen with the access point, and if it com...
Hi team, we have installed c9800 HA pair 2 months ago, running 17.12.4 version. We are facing now random reloads of standby WLC every few hours with this info: Reload History: Reload Code: ReloadReload Description: Reload Command - RIF: Bulk Sync, sy...
