Wireless

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

review


Labels

Forum Posts

Hello, I'm wondering if its possible to override the default WLAN AAA servers using a Flexconnect Group?   I see there is an AAA option under Flexconnect Group however when adding a different ISE PSN to the default configured on the WLAN, I couldn't ...

Hi Guys,   Just after some real world cases of surveying for VOIP deployments in retail deployments alongside Zebra devices. Now, skype we'd usually look to -62 to -65dbm for RSSI using a generic tablet profile in Ekahau.   Given the customer also us...

We are seeing random/sporadic/in-repeatable disconnects from our Wireless LAN.   Examples of the errors we are currently seeing on the WLC are;   AAA_AUTH_SEND_FAIL: 1x_aaa.c:849 Unable to send AAA message for client dc:53:60:d6:de:31*Dot1x_NW_MsgTas...

ritchgaz by Visitor
  • 5192 Views
  • 4 replies
  • 0 Helpful votes

Hi WLAN Guys,   I just stumbled over this Cisco-Promotion.   https://www.cisco.com/c/dam/en/us/products/collateral/wireless/nb-08-access-point-promo-flyer-cte-en.pdf?oid=pbnew008897  BUY 2 Cisco Aironet® 802.11ac Wave 2 access Points and  get one fre...

Please move if this is not the right forum.   We have a 2500 wireless controller and it seems that one of the ports is going up and down.   The logs show some errors for the AP on that port but I am not sure if the port is causing the AP issues or th...

itguy1024 by Level 3
  • 1127 Views
  • 3 replies
  • 0 Helpful votes

I currently have 2 floors and a basement.  Each is about 2000 squarefoot.  I currently have 3 routers, one on each floor.  The internet is gigabit fiber.    The problem I have is that my area has poor cell service, so I use wifi calling in the house....

  Does anyone know how to enable this setting via the GUI in 8.3.148? I need it for documentation purposes. As far as I can tell, this setting can only be enabled via CLI, which seems at odds with Cisco's GUI configuration.   config network secureweb...

RBenke by Level 1
  • 1038 Views
  • 2 replies
  • 0 Helpful votes

I have 2 WLC 1st one is 2504  2nd one is CTVM  my problem now is : in 2504 i have 11 as management Dhcp VLAN with range of ip , and i have SSID (name:SOFT) on vlan 15 and its with DHCP also , and this vlan (15) with internet service , the APs took hi...

Murad* by Level 5
  • 1046 Views
  • 3 replies
  • 0 Helpful votes

Hi, we have a client who has a big warehouse already covered with old Cisco wireless access points (1242 model) and has (AIR-ANT2460P-R) connected to majority of the AP's..   I need your help confirming that the access points (AIR-CAP2702E-E-K9) will...

Ahmad T. by Frequent Visitor
  • 1188 Views
  • 1 replies
  • 0 Helpful votes

any idea why iphones and ipads are not connecting to 802.11ac? it is always connecting to 802.11n. even if i turn-off wifi off and then on, it is sticking with N. anyway i can configure the controller to allow these devices to always connect to AC?  ...

rlaudiano by Level 2
  • 8220 Views
  • 15 replies
  • 0 Helpful votes

Good morning,We have a customer with a 5508 controller running 7.4.110.0.  It has a backup image of 7.2.111.3.When we added a 1242 access point to it recently the access point was offered the wrong image version: it was offered and downloaded 7.2.111...

Review Cisco Networking for a $25 gift card