Welcome to the Cisco Community Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, September 14, 2026 through Monday, September 28, 2026. Our experts Shree Hari AB and Suman Sinha wi...
What is the best way to verify the antennas have been aligned correctly? Another post recommended reading the RSSI value, but I'm not sure where this is found on a 1532? The AP's are connected to a controller and reachable on SSH.
Hello All, I have a situation where clients are not able to get IP address from DHCP pool when attempting to connect to a office ssid : campus. where as same users are able to get IP address when connected via wired to the switch that is connected...
Can anyone let me know if we can do inline upgrade of Cisco Prime infrastructure Virtual Machine from 3.1 to 3.3 ? As per the quick start guide , it is mentioned that for upgrading from 3.1.x virtual machine to 3.3, a new virtual machine should be ...
Looking to implement temporary GuestWireless Design prior to while the ISE deployment is in procress. Went with NextGen networking for WLC 552 and AP 3800. Since the WLC dos not support DHCP does anyone have any suggestions for GuestNetwork design. W...
Trying to setup a wireless bridge between 2 1542 and a 3504. I have the 1542 joined to the controller and under the wireless tab set in bride mode but on APSub Mode i can not select a different function. Under AAA/mac filtering they are added in ther...
Evening All, I have a few questions regarding Wireless WLC and ISE , The best way to configure the following . 1. A guest network that can use a token to login and change every day,week etc. I see the token option on ISE but cannot find any do...
Hi Everyone, I have a little problem which i would be grateful for the help. I have setup with a virtual wlc, a PAN and PSN , an AP and a laptop with anyconnect client. There is a mangement interface (ESXI) and two SSIDs created for internal and gues...
HI everybody, sometimes,i will see “XOR” in wireless，but i cannot understand what's meaning about it. So,i want to know it's full name and fuction about it. Thanks a lot!
Hello All, I set up a wireless network one years ago with one WLC ( model:2500 version:8.1.102.0) without any probleme. Since around two weeks, performance go down only for the wireless network which is a part of the local wired network (no vlan). I...
Employee VLAN currently has more than 500 clients and causing broadcast issues. We are planning to split them into two /24 VLANs say 40 and 50. And then map the employee SSID to a pool of two VLANs.However the UI does not allow to put two VLANs on VL...
Hi Everyone, I have a query related to Cisco 1400 AP. We are using AIR-BR1410A-A-K9 in bridge mode as p2p. Unfortunately one AIR-BR1410A-A-K9 gone faulty from the pair. We are now planning to buy cisco AIR-CAP1532E-A-K9. My query is Will AIR-CAP1...
Hi all, I have a mobility express controller which it's switch port is an access port. As soon as I change it to trunk, the controller will become unreachable. What is the problem? I have another environment with the same APs and controller and...
In my warehouse environment, i have 27 AP (AIR-AP2802E-K-K9) configure with Cisco mobility express and security WPA 2 Enterprise with using local radius server. I am facing issues is when my mobile devices success connect to my WiFi with WPA2 Enter...
Hi Folks, I have a question related to a MU-MIMO (Cisco 1830 LAP) access point. But I think this applies to all MU-MIMO access points. Could a MU-MIMO access point serve a 802.11g and 802.11n/ac clients simulteniously? Thank you.
I am having an issue with the quest network. I can jon it but it does not give me an ip adress, and if I manually assign it to the scope on vlan 2 i still do not get any communication. Assistance would be helpful.
