Hi AllWe're required to do a firmware update on our wireless access points as we're very out of date. We have the following Meraki Wireless products in production which i believe are all compatible with the latest firmware based on my research. MS350...
Forum Posts
Hello Cisco WLAN Experts,this university hospital recently started to use Identity PSK for IoT-devices. I changed the configuration of an already existing WLAN for PSK-Authentication of old medical devices not able to use WPA2 in the past, to authen...
Hi We are facing Meraki MR42-44 auth_mode='wpa2-psk' 11k='1' 11v='1' error_code='17' radio='1' vap='0' channel='64' rssi='33'We have no SD WAN. only cisco meraki and tplink er8411 router. all clients suddenly facing that error 17 1. auth_mode='wpa2-p...
I'm using a WLC with APs configured to only use non-DFS 5GHz channels (Channel 36, 40, 44, 48, 149, 153, 157, 161). In the RF Profile, I have explicitly disabled DFS channels.WLC:C9800-L-F-K9; version:17.9.6AP:C9120AXI-T; version:17.9.6However, I sti...
I have a network with a mix of wireless access points...Cisco CW9162ICisco CW9164IMeraki MR42All devices are managed through the Meraki dashboard. In the dashboard (Wireless-->Configure-->IoT Radio Settings) BLE scanning is turned on, and on the indi...
Hello, i have a cisco meraki access point with normal password login and i am using it in commercial premises and want to secure my wifi network...i now want to setup a system where when a guest clicks on my network SSID he needs to login with his em...
Resolved! Is the device really blocked?
Hi All, Would like to see whether this is 'normal' for everyoneFrom the clients page of a device, device policy is set to Blocked (all), followed by Save. I gave it 5 min and then click disconnect client. I then waited another 5 min and refresh the p...
Folks ,Is it possible to bypass 802.1x authentication for a wireless client (iPad) in Meraki ?
Hi Experts I have a cisco access point CW9166I-A. It was successfully joined with the C9800 controller. However I noticed the access point is losing its ip address after every couple of hours, and ICMP request back with RTO. I had to reboot it every ...
Hi all; As you can see in the following figure, my current Virtual Interface IP Address is 192.0.2.1: Although I can change this address using CLI, I want to know that how can I change this address using GUI method in C9800 17.12.05 box? Thanks
Resolved! When is FlexConnect active on an LWAP?
Hello, everyone. I've seen some conflicting explanations about FlexConnect so I came here to verify how it really works. Here are snippets of text from my study resources: One implies that FlexConnect is active and that an AP can locally switch data ...
Resolved! 9166 Not Leaveing CAPWAP Discovery
Hi cisco community,We have recently deployed a 9800 WLC and are attempting to join several 9166. I have confiqured DHCP 43, and DNS A record which appear to be working. Routing between WLC and AP is functional and DNS entry is resolving correctly. I ...
Resolved! LocalAuth and 6E
I have a number of sites which are remote from the core network, for which I have deployed Local Auth. However, I want to upgrade the sites to 6E, which at present does not play nicely (in the Meraki world, anyway) with Local Auth.I guess enabling 6E...
Hi,When the access point reboots, it suddenly goes into the init>> state. I tried finding a solution to resolve this issue, but I couldn't sort it out. Are there any other ways to address these kinds of problems?Please choose one of the following boa...
Splashページでユーザがアカウントを申請後、アクティベーションせずとも10分間のインターネットアクセスが出来てしまいます。アクティベーション前のインターネットアクセスを制限する、もしくはアクセス出来る期間を10分以外に設定することは可能でしょうか。ご存知の方がいらっしゃいましたらご教示いただけますと幸いです。
