DOes anyone know how to reset CUCM to default setting or preferably reconfigure it?
DOes anyone know how to reset CUCM to default setting or preferably reconfigure it?
I’ve read conflicting datasheets and documentation stating both the 1572EAC and 1572EC provide 802.3at PoE+ out if powered via AC or DC. Other docs allude to this only being the case on the 1572EC with cable modem backhaul. Can anyone confirm that...
Having a small issue with our Splash page not updating. After making changes to the text, having it preview okay and saving it the changes do not appear when users connect to the SSID.
Hello, how are you doing? I was watching Jerome Henry's VoD from CLive Cancun 2017, BRKEWN-2005, in which during the video recording he hided slide 76 (which is present in the PDF). This slide talks about MAB. MAB in RJ-45 ports is well understood, b...
transfer speed is low and falls sometimes occur, Customer uses cisco ap 1600
Hi All I have two controllers (AIR0WLC2125-K9) in my network. There i have many W LAN's created, one of the wireless LAN e.g TEST. Users connected with it.When of user disconnect from it and come again next day they can connect without any issue b...
Hello We would like to use an anchor controller in order to setup a managed guest service. The guest service will be provided by an external partner, the APs with GUEST SSID are in the customers network in different remote locations. The idea is to...
Hi,Is it normal that Air Marshall detects Meraki APs as spoofers or sending malicious broadcasts?I'm seeing hundreds of these messages seen by different Meraki APs. At this case, the offending MAC is the main MAC address of the same AP, however we sh...
Hello Team, vWLC 8.4.100.0 AP 2702 I have configured flexconnect (central auth, local switching and is working perfectly fine). I have a WLAN with interface putting my users in the right VLAN switched locally. But so far i had in WLAN advanced ta...
The scenario: Site A: 2 Cisco 5508 Controllers and 1 Cisco Prime appliance. Site B: 2 Cisco 5760 Controllers and 2 Cisco 5508 Anchor Controllers. The Prime manages all the above controllers. Now a 3rd site(mother ship) with an instance of prime w...
Are there any Dashboard APIs that give you the subnet mask of the uplink interfaces?
Hi all I've got a new WLC 3504 with 8.5.110.0 which I just installed. What I haven't managed though, how can I, if it is even possible, assign a VLAN to one of it's physical ports? I have connected the port 5 to a Switch with a trunk and my idea is n...
2504 FW 8.2.151.0 with 6*3502 APs, 802.11n clients. Network Summary, Clients screen shows Usage and Throughput stats. What is the significance of these figures? What would be good ranges for both?
Currently my users can't access public wifi because they are re-directed to the proxy before they can get to the public wifi landing page/terms & conditions etc. I need to allow them to log on to public wifi but then route them to the proxy after tha...
hi everyone i have WLC 2504 with 15 AP 1142 , firstly how i can control a broadcast of 2.4 or 5 ? and my question here if i want to transmit 5ghz (because it better than 2.4 in rate) but its cover small space than 2.4 so i want to put 5 ghz as primar...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 10-15-2026 05:58 PM | ||
| 10-12-2026 06:46 PM | ||
| 09-30-2026 07:34 AM | ||
| 08-10-2026 11:32 AM | ||
| 08-06-2026 09:29 PM |
| User | Count |
|---|---|
| 5 | |
| 2 | |
| 2 | |
| 1 | |
| 1 |