Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
What may prevent wireless users attending video conference from excessive segment/packet loss? As of now when 4-5 attendees participating in a video conference, complain of bad reception. What is to prevent collisions of segments during video trans...
Dear all I want to provide wifi solution for hotel guest.The requirement is as below. - Provide wifi service to all area - ID/Password will be assign per guest with limitation date. - Bandwidth control per SSID - To assign guest's ID at reception of ...
Hi, I have Cisco Aironet 2700 series AP that I have converted from LWAP to Autonomous. Can someone direct me an to-the-point article or steps how to configure it (official documentation is too much and you are almost lost to find the correct configur...
With Telstra enabling 4GX (LTE-Advanced) in my area, I am curious as to Cisco device support for this protocol? We currently have many 819 LTE routers, would a software upgrade be available to support carrier aggregation on the existing 819 devices? ...
Resolved! Radio0-802.11N2.4GHz Radio1-802.11AC5GHz
Hi, I am configuring Cisco Aironet 2700 series AP in autonomous mode. I have created SSIDs for both 2.4 and 5 GH (SSIDs are Identical). 1. Only 2.4 GH SSID is availble on clients side ... what may I have done wrong here? 2. PCs are not able to list a...
Hi, I am trying to configure an AP and following this video: https://www.youtube.com/watch?v=5RE55VBsyDE If I do exactly what is mentioned in this video, I am able to configure AP. On some client Machines AP is available while other can not find that...
Hi folks. I would like to know why my WAP4410N access point does not allow to change the country operation mode. In the list box only the USA is available to select. Thanks in advance.
I cannot access the secondary controller, which is active after failing over while testing HA redundancy. The weird thing is, as soon as I enable management over wireless, I can then management it over wifi while failed over to the secondary. But, a...
Hi , I am facing an issue with 1852i Access points. b/g radio is working fine, whereas 'a' radio is not working. WLC Model 25054 and software code is 8.2(X) AP Model : 1852I-I-K9 Cisco Switch Model : 2960X 370W Currently, I am in UAE, but the AP mo...
Hi! May we know what configuration is required on a Cisco POE Switch Side if we need to have multiple SSIDs for our Aironet 2600 Series and different IP Ranges for each SSID and VLAN? The DHCP Server is a hardware firewall. Thanks.
Hi , I am facing an issue with 1852i Access points. b/g radio is working fine, whereas 'a' radio is not working. WLC Model 25054 and software code is 8.2(X) AP Model : 1852I-I-K9 Cisco Switch Model : 2960X 370W Currently, I am in UAE, but the AP mo...
Hi, I am using Cisco WLC2504 controller with 3502i Access points. I would like to create 2 different SSIDs. SSID-2.4: Just enable 2.4GHz radio on this SSID. SSID-5.0: Just enable 5GHz radio on this SSID. Does anyone know how to achieve this? I spent ...
I want to build tool to monitor the WIFI area in a building. So I need to retrieve all the information about the connected devices to the access point. my question is : if there is any API which able me to retrieve the information such as RSSI and o...
We have a setup with one 4402 WLC and 7 AIR-LAP1142N-E-K9 APs in an environment with around 200 clients. Without any clear reason, clients are intermittent loosing internet connection. Client are registered to be connected to the controller, however ...
Hello, We currently are using Cisco Prime Infrastructure 2.1 (2.1.0.0.87) and have multiple site locations that are "shared" such as office buildings. Due to this we have a rogue report going over 2000 pages, and I am looking to cut that down by eli...
