Welcome to the Cisco Community Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, September 14, 2026 through Monday, September 28, 2026. Our experts Shree Hari AB and Suman Sinha wi...
Hi, We are running two Wireless network such as Corporate Wifi and Guest Wifi on the same Wireless Controller and Cisco ACS. For the guest wifi, we are just adding or registering the MAC address of guest devices then they are prompted to accept the t...
Hi, We have a pair of WLC 5508 and not sure what happen but cannot console to either of them. All is working fine and and we can manage it by web-page but not by console. thinking of power-cycle them ? Any suggestions are much appreciated Thanks Q
With flex connect you have an interface on the WLC, vlan mappings under AP settings, then trunk ports on the switch that go to the AP. They all have vlans associated with them. by default the vlan mappings under AP settings take the interface vlan on...
Hello Masters,we have one central location which is connected to 4 Different Sites via Radio point to point link. on each site we have 2800 series cisco router, Dell Power Connect Switches. I am using Ether Channel between router and switches for loa...
I am doing the default startup configuration , LAPs successfuly joined the WLC( 5508) . The 802.11 radio are all up , SSID is broadcasting , however, I an not able to see it. See the below show commands (Cisco Controller) >show advanced 802.11a summ...
Hi, I have vWLC version 8.3.112 and AP 1562i with power injector. I want to check is this AP is working as 3x3 or 2x2. I have check that this AP required a power of 32W to give 3x3 for that I used power injector. So is there is any way to check the...
We've been able to install user certs on our 7925 phones for years, using our MS 2012r2 server CA, with a SHA-1 server cert. We recently upgraded our CA server's cert to SHA-256. Now when we try to generate a CSR from a 7925, the phone always prese...
Good afternoon! I'm new in Cisco and looking for information about bandwidth rate limiting ways for different deployment scenarios. As I found, it's not possible to tune rate limiting for 2504 hardware controller. What is default behaviour in this ca...
Hi, I cannot find the difference between AIR-PWR-C and AIR-PWR-B. Maybe someone can help. Can I power an "old" AIR-CAP1602I-E-K9 with AIR-PWR-C? Is AIR-PWR-C per default delivered with AIR-AP1832I-E-K9? (In the data sheet and getting started guide I ...
Hi, 1. Just trying to understand the dynamic TPC on the Cisco 5500 controller on the 5 GHz band and 20 MHz wide channels (keeping the example simple). The default settings enable TPC adjustments between the Max (30 dbm) and Min (-10 dbm) power levels...
We have two (2) WLC 5508 currently in production, each with associated Access Points and Wireless devices. Now we would like to configure the redundancy between the two wireless controllers. I have not done configuring two devices in production with ...
Is there a good document available that details the latest (April 2017) thinking and best practice for the use/config of a single WLAN/SSID supporting PCs running softphone and or interactive voice/video (Skype, Jabber, etc.) in a controller based wi...
Hello, i have installed a 5520 as the local controller und a 2504 as the anchor controller. Both coltroller have the code 8.2.151. Every thing goes up and it look fine, but the clients have a slow connection. Here are my questions: 1. Is the combinat...
Hi I have taken a new broad band connection, which I am not able to use it through my WAN4410N wireless access point as the service provider says this router does not support PPPoE. Can anyone please help how to enable PPPoE or any alternate ways to ...
Have 24 of the Cisco model 2702I access points and a pair of 5508 controllers. ISE is being implemented. How does it handle it when a client moves from one AP to the next? Is there anything we need to be aware of?
