Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Hi ,->How can I configure CW9166 Access point into dual-band mode with specific bands active and deactivated, such as having the 2.4GHz and 5GHz bands active while keeping the 6GHz band deactivated, or alternatively, configuring it with the 2.4GHz an...
Hi AllI m planning to deploy a Wifi 6 SDA solution that will comprise 2 borders switches with Embedded Wirelless Controllers .What would be the best way to implement this assuring that Wireless controller redundancy is also available . All documen...
Hello, I wanted to Convert 9105AXI to EWC mode but failed with this error AP-V01#ap-type ewc-ap tftp:/10.10.10.2/ap1g8 tftp://10.10.10.2/C9800-AP-iosxe-wlc.bin Download script called with args:[-l tftp://10.10.10.2/C9800-AP-iosxe-wlc.bin -m 2] Sta...
Hello all,We have swapped 2800 for 9120 APs 1 for 1 in a office, which are connecting to AireOS 5520 8.10.183.0 WLC. THere was never issues reported within this site, but after this 1 for 1 swap, we are getting bombarded with INC of signal issues, wi...
Resolved! WLC Netflow
Hello,I have WLC 2504 and AP in Flexconnect mode, then i enabled netflow on the WLC and after some hours i can't see any netflow traffic.Can i know i can't see any netflow traffic due the AP is in flexconnect mode?
Resolved! ACL / WLC / ISE Question
Hi everyone,Thanks in advance for taking the time to read this post and for any advice or help offered.I am a contractor working for a customer. I am familiar enough with Cisco switching, but this is my first exposure to both Cisco wireless/WLC and I...
hi,current production running a pair of C9800 in HA w 200x connected AP.If i make changes to the existing Policy Tag that is in use; example - add a >new< WLAN + Policy profile orexample - Change existing WLAN profile authentication protocol use.what...
Background:I am setting up mesh wireless on a 9800.I am going to import several mesh APs from a 5520 controller and add some new ones. I am using a converted configuration.The converted config only has username, macaddress, mac. No WLAN specified.Con...
Resolved! 9800 deployment in multiple sites
In deploying 9800 to multiple sites (3 or more) is there an option to deploy in HA setup? I saw SSO but it only requires 2 devices. or is there a way to configure the 9800 in 3 standalone setup but users can seamlessly connect to wireless as if regi...
Hi all, I'm trying to setup a 9800CL without any vlan. I can set it up and get an IP while using vlan1 from my DHCP server but for some reason I cannot see NASes when I connect my MacBook to the AP connected to the 9800. I can connect to them if I go...
My organization has been running 2702 APs connected to a 5520 controller. We have purchased 9105 APs and will purchase a 9800 controller in the next procurement cycle (mid-to-late 2025). I know the 9105s can associate with and be controlled by the 5...
I would like to request your assistance and expert insights. I'm experiencing an issue with the AIR-CAP1702I-Q-K9. When I connect the console cable to it and attempt to operate it via the terminal, it fails to respond. A few minutes after startup (wh...
Hello , Can you point me the procedure to configure the Cisco Catalyst AP 9100 series in WPA2 mode? The configurations I tried are not working. With continuation to that, I want to configure the same AP in Enterprise mode with external radius server....
Hi. I have a 9800 WLC that has been configured via CLI. However, when I access the device via web interface it starts off with the "zerodayconfig" as if it is right out of the box. There doesn't seem to be anywhere that I can bypass this and I'm won...
Need to know, does this model C9120AXE-K support autonomous mode? For branches that need to be standalone unit, with no need to connect to WLC or flex connect configuration.When I convert this C9120AXE-K to ECW, it stop all process and revert back to...
