Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Resolved! Clean air -- how to interpret
We are new to clean air. Having turned it on about a week ago, we're seeing less than perfection on some APs. The attachment shows two days of "minimum" readings for one of our 2.4 Gb/s radios. Others in the same building show similar "less than perf...
The title exactly sums it up, just having a hard time finding if anyone could link me to a site showing a compatibility matrix that the 5508 WLC will connect to a 2700 series AP. I am having an extrmely difficult time finding this for some reason, an...
Hi, Due to various reasons, I've been asked to limit the number of wireless controllers in our infrastructure from 4 (2 on the LAN side and 2 in the DMZ) to 2. I am considering removing the DMZ controllers which are currently serving Open Guest Wifi...
Hi Guy’s, I'm not a wireless guy so - this is new to me I’ve got 2 switches: Ground Floor ZAOBSW01 - Wireless Lan Mobility controller Installed 2 x1702 access point Each access point broadcast 2 SSID's (TA_LAN & VC_Board_1) 2nd Floor ZAOBSW02...
Hi guys, we bought a couple Cisco 3502i V02 APs. The PART# is AIR-CAP3502I-A-K9. The 5508 controller is running 7.6.130.0 and has other 3502i APs registered to it. Its set up with multiple countries, including the US. We still have free licences. The...
Resolved! Wireless Regulatory Domains
Good morning, we purchased 10 Cisco 2702i APs. Two of these APs came bundled with a WLC. These 2 APs are of universal domain as opposed to the regular domain for the other 8. What is the difference between universal and regular domains? I am based ...
Hello all,i have a problem on a bridge between two AP 1530.Using dotradio0 interface with 2.4Ghz i can associate Non-root bridge with Root bridge while when i try to use Dotradio1 interface with 5Ghz i get the error message : %DOT11-4-CANT_ASSOC: Int...
We have two WLCs running software version v7.6, and are going to upgrade them to v8.0. The APs joined to each controller have the local one listed as their primary and the other listed as secondary, providing failover should either controller fail.T...
Hi guys, Within two months, I got 3x WLC 2504 RMA approved and been replaced !! Is it just "murphy law" or I'm very bad lucky... or YES, its the reality and WLC 2504 are very sensistive? I'm very tired of this, and I'm starting to think to not sug...
I have a new primary 2504 that is running 8.1.102.0, and an HA 2504 running 7.6.101.1. Question is, can I download the IOS from the primary 2504 to the HA controller? Does it matter if it's an HA controller? Thanks
Hi, I am not sure if I have placed this question in the correct entity. But we are experiencing a weird behavior in our wireless network. We have a WLC in HA AP-SSO setup with 1602i and 2602i Access Points. We have 2 SSIDs, 1 for guest and the othe...
Hi What is main feature of WLC 4404 that 4402 does not have ? or send me a link. I want to buy WLC for ccnp/ccna lab. Thank you
We discovered that the WLC was generating a lot of traffic that turned out to be multicast. The additional traffic causing problems with voice. We have been steadily increasing the amout of Apple devices we have. We upgraded the WLC software to 7....
Hi all, I am trying to find some instructions to setup the following - AIR-AP2702I-UXK9 I want to run in autonomous mode and it has come with the combined image. It is currently loading like a unified image, how do I convert it? Brad
dears I have in HQ internal WC and guest (anchor) WC. Users in HQ can access internal network and internet via wireless network using 2 SSID Is it possible to install one AP in a branch and connect the AP to the controller in HQ. then users in branc...
