Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 17 , 2026 through Tuesday August 31, 2026. Our experts Saikat Nandy and Prashanth Bargur Hanumantharayappa will be waiting to assist you and resol...
Hi, I have a Prime Infrastructure with one controller and one MSE used with WIPS license. I would like to add another MSE with CAS license, but I am not sure I can assign the controller to both MSEs. So my question is : is there a way to run the two ...
I have a WLC 2504 of v7.6 with L3 web-auth enabled. Its clients got deauthenticated from time to time. SNMP trap revealed that clients were deauthenticated with reason unknown and the reason code was 103. I checked the deauth reason code online but...
I have been configuring some access points on a 2504 controller. Every time you make a change you get the warning saying this may disrupt clients etc. Tick the box if you don't want this I had ticked the box and now for some reason cannot make any...
Hi Guys, I need to install CA certificate on WLC for management and Guest webpage so that the users don't get an error message and is more secure. I am trying the old method of using open ssl 0.9.8 for generating the csr for wlc. Should i be followin...
I'm looking to move to cisco wireless for my home. just wondering what the difference between V01, V03, V08 is.... I figure its hardware revisions but does anyone know if there is a version to stay away from or if there is a version to look for since...
Hi, Is there a guide to configure multicast on a 1830 AP with mobility express controler. Is it supported?
Hello All, Cisco AnyConnect Secure Mobiility Client: 4.2.03013AnyConnect Network Access Manager Module: 4.2.03013 Operating System: Windows 7 Professional We are coming towards the final stages of our roll-out of Cisco AnyConnect + NAM Module + ISEPo...
Is it OK perform a 5GHz Heat map Site Survey with the 2.4 Ghz radio enabled on the AP? Using the AP-on-stick method. I would be just looking at the 5Ghz data to determine the coverage and ignoring the 2.4 Ghz data. Anything wrong with this? or must I...
we have wireless service module ,how to check the client connection throughput for bulk users ,we may have around 1500 concurrent users. is there any command to see all the users connection speed at once.it is difficult for me to check individually (...
for wism-1 controllers and 5760 wlc when a client connected to the ssid for a same controller(wism or 5760) the connectivity is getting disconnected for every one hour. after client reconnect the ssid of same controller it working but one hour it i...
Hello,I am using Cisco WLC 4400 and four Aironet 1242 LWAPP.I would like to get detailed informations about RSSI of all probing clients (rouge clients, associated clients, and all the other devices that are just probing for a wlan).It would be great ...
Hi, from time to time I have wifi guest users in my network who will not be redirected to the /guestportal/ page on ise. This is not a problem like "there is a proxy configured on the device etc". This must be something different because client looks...
Hi , Good day! Is any one have tried to add an additional AP license on Cisco WLC 5508 with HA configuration. Is it okay if you could share your procedure and best practices to execute this? Hoping for your responses Thanks And Regards, July
Hi, I have recently added a new AP in my office close to another AP, which are being managed by Cisco WLC. Could you please give me a brief idea about how to optimize the radio frequency or channel utilization? We've got 4 APs and two of them are ver...
Hi, We have centralized WLCs in datacentre to which all APs in campus associate. The VLANs in DC are different from the ones in campus (VLANs don't extend). There is a requirement in one lab (currently 2 APs) where the wireless users should be on the...
