Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
I have a Aironet 1602e in autonomous mode. If I log into the CLI and issue the command "show dot11 associations client" I can see the list of client devices by MAC address. Is there a way for me to configure the Aironet with a name for each device?...
hello I have a 100 access point (AIR-CAP3702i),99 are joined to the controller 5508 version 7.6.130 and take the same version of the controller exceptone of them it take 7.6.118 and all configuration is the same .the behavior of the access point is ...
Hi Everyone,Well, just what the subject says.For stability it is recommended to manually set the backhaul freq right?Anyway, I was just asking if its OKAY to MANUALLY SET the frequency ONLY in the RAPs.Im thinking that the MAPs will automatically neg...
Hi , ı have cisco 7921 ip tel .its authentication method is 802.1x + CCKM . But sometimes , I get ip configuring error some loaction in my bussiness and when I powered off and after powered on , then it is okCan you help me about what is my problem
Do we have Option to add MAC address of specific laptop or Mobile to connect to the Access Point in cisco Aironet AP 1260 series in Autonmous mode
I can not manage the access point AIR1532E (AP1 configured as Mesh rootap) connected on a tagged Vlan port (of switch B)from controller AIR-CT2504 connected on a tagged Vlan of another switch (A) port.If i connect the mesh AP to a controller port, ev...
Hi. Does anyone has any experience in adding an extra vCPU to the Cisco Virtual Wireless Controller. The standard config is 1vCPU and 2GB RAM. My question is: Can I add an extra vCPU? Thanks in advance.
we're using same ssid wireless_guest across organization. At remote location wireless guest going back to head quarter via T1 line. I want this traffic going out via DSL line. What would be a solution to overcome the issue ...not getting to wireless ...
Well I bought two of 3602i but I am wonder about 802.11ac module can be used in autonomous mode, does it should enable through autonomous? I do have mostly all clients that has 802.11ac for now so I upgrading from 3502i to 3602i with module.
We have a situation where our LAP have been installed so closely, that the "802.11a > RRM > Tx Power Control(TPC)" has set the power level to 7. Consequently there are rooms that cannot see a 5 GHz signal. Why can't I just up the power of all 40-odd...
Hello,Is there any possibility to limit the bandwidth per SSID on Cisco Aironet 1100 that is connected to Cisco router 876?So the main goal is to have two SSID one for the guests and one for the colleagues and to limit for example half the bandwidth ...
I have a single stack of 3850 switches to which my APs are directly connected.My APs are registered and I have created 2 WLANs to which I can authenticate, associate and pickup an IP address just fine. VLAN 53 - Wireless APs (no WLAN configured) 10.3...
Hi,we have impelmented wifi solution over our network, we have used the option 82 to help in assigning IP addresses to the clients. the Setup is mainly as below,Cisco WLC 8500 --- NAS " Third party" --- AAA server. using RADIUS Protocol.we dont have ...
p { margin-bottom: 0.25cm; line-height: 120%; }a:link { } I have some problems with ISE Central Web Authentication deployementWhen the user associates to the web authentication SSID, and opens the browser, the WLC redirects to the guest portal, onl...
Hello all,Heard that Cisco has announced the end of life for 1262 series Access points. Can anyone suggest the best replacement for this series of Access Points..
