I have access point CW9162I and I want to configure them in mesh.I have checked the documentation but it is not clear to me what the step by step is.So my theory is the following:1.-I connect an AP "AP1" with internet access.2.-I connect a second AP ...
We have a spare wlc9800-40 we are trying to use but it keeps rebooting over and over with below. I've tried to boot from various versions and still get the error output below. It seems to think there is an HA pair that its not seeing so it reboots...
I have an issue regarding on the Lobby Ambassador Admin of WLC9800 where the credential is configured from Cisco ISE TACACS+ Initially, it can log on successfully using the username and password configured from Cisco ISE TACACS+, however, it immediat...
Hello,I have two switches 9400 redundancy SSO , I create SSID with different VLAN only one work VLAN 145 I can ping the gateway from WLC but for the other impossible to ping other gateway!!! , I allow all vlans in two ports same , can you please hel...
Hi all,Is there any technic to set quota limit for wireless client in meraki dashboard. I want to set quota limit for those clients who have exceeded bandwidth .For example - Quota for one day let assume - 50MB, If client excided for than set bandwid...
Hello,I have a number of Cisco 3502i WAP's and that product has been completely removed from the Cisco website. I know they are end of life, etc. but surely the data should be preserved for reference.Here is the pertinent informationAPMACAddress#sh v...
Looking for solutions on how to limit the amount of clients that are allowed to connect to a singular Meraki MR36 without interfering with the SSID itself.
Hi Team,I would like to confirm if this Access Point Image Version Number 17.12.3.31 is compatible with 17.9.4a cupertinoDevice ID: AP505C.88D5.872C Platform: cisco C9120AXI-A, Capabilities: Router Trans-Bridge Interface: GigabitEthernet1/0/38, Port ...
I have installed a 9130 EWC and it is running version 17.9.6 successfully.I also have a 3702 running in lightweight mode with LWAPP image version 17.9.6.40 to match. However it will not join the EWC controller.On the 3702 side I see:*Feb 1 04:41:49.0...
Hi all,Looking to design/deploy a couple IoT enterprise wireless networks. One of the WLAN networks will have access to the Internet only. The second WLAN will have access to the Internet as well as the internal (trusted) network. Could I leverage...
I'm working on configuring the Cisco AP 9115-axe as embedded wireless controller. So far I've changed the AP to EWC mode and configured the hostname, IP and route. AP is connected to Cisco 9200 switch running version 17.9.4a, EWC is running version 1...
I have a Meraki solution consisting of 6*MR42, MS220-24p, and MX84.I am facing issues with connecting IoT devices, which I suspect might be due to the Access Point (AP).I would like to upgrade step by step, which model of AP do you recommend as a new...
I am deploying Meraki in my outdoor athletic complex and need an advanced captive portal solution. I need custom fields for detailed customer data collection such as emails, names, numbers, etc. The solution should integrate seamlessly with our exist...
【問合せ内容】Merakiご担当者様Meraki MR44 及び Meraki MS120-24Pを利用した、ファームウェアアップグレードを検討しております。ファームウェアアップグレード動作について何点か不明点がある為ご回答を頂けると幸いです。【質問】 製品型番: Meraki MR44 / Meraki MS120-24P①Merakiクラウド上でのファームウェアのアップグレードを実施予定ですが、 過去の実績ベースで成功率や失敗率など情報はございますでしょうか？ MR44(約110台)、MS1...
Im in the process of replacing our old unifi wireless system with new meraki CW9164I access points and im running into some issues with some of the access points. I getting alerts on some of my acesss points that says "Uplink IP address in conflict w...
