Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 17 , 2026 through Tuesday August 31, 2026. Our experts Saikat Nandy and Prashanth Bargur Hanumantharayappa will be waiting to assist you and resol...
Hi All I had a brand new 2802i which had an issue with booting up. It only showed the green LED flashing. After attaching a console and booting it again, I saw that it landed in ROM mode. I might have accidently unplugged it while it was booting up t...
Looking for any insight into a possible migration from Ruckus APs (R710) and Brocade switches (7250) to Meraki.We use Meraki MV Cameras and evaluating Cloud Controller for Ruckus vs possibly moving over to Meraki switches and APs.The main con is the ...
1. Integrated Meraki with Azure AD for authentication2. Authentication expiry is 30 daysPost expiry, splash page pop up is not coming even after forgetting the SSID and re-entering the psk. No request is coming to authentication server if trying from...
Hello, I have set up a Cisco AIR AP2802E with Mobility Express. It also gets an IP and the LED is constantly green. However, I cannot access the website. I keep getting the message in the browser that the connection failed. Does anyone know why this ...
So for a long time already I'm considering to change the authentication from WPA2 to WPA3.But, I keep reading here and there, that user's are having more issues with it, or are affected by this change to the worse.Any reasons why it's recommended to ...
Hi Putty console can logon to AP1140 and WLC. Why SecureCRT console cannot work well. Sometimes CRT cannot logon to AP1400 at all. Even if logon to the AP, I cannot type any thing at all. Thank you
HiI was looking for an updated and reliable reference about what 5Ghz channels are usable for outdoor deployment in France or at least in Europe.I'm not talking about mesh infrastructure but about an enterprise deployment.I had a lot of readings and ...
Team,We have configured Cisco ISE with MR46, but when I try to send a session reauthentication request or termination, it does not go through. What could be the reason?Once a user is authenticated, I cannot kick them out of the network. I'm not sure ...
I am going to be replacing a pair of 5520's with a pair of 9800's. My 5520's are in a N+1 design. We did this because it gave me a controller to use for testing configuration changes and OS upgrades. I've read through the 9800 documentation, and I am...
I have three CBW150AX APs in my home. Recently one disconnected from the group and was blinking red/green. I upgraded the Primary and second AP to the latest firmware 10.6.2.0. They are working fine. I factory reset the disconnected AP and have be...
Hello Team,Could anyone recommend resources for self-paced learning on wireless technologies from the beginning? Like,What is dB?How to calculate dB?What are RSSI and SNR?How does signal penetration work over obstacles?Additionally, if we need to mou...
Hello all.Is there any best practice for "DCA Channel Sensitivity", especially for 2.4GHz band?I'm generally cautious about adjusting these types of settings but I would like to know from you all about your experience on changing DCA channel sensitiv...
Hi, i want to create a unavaliable MR's report about the time that all MR's became unavaliable in the month, then calculate the percentage that it became unavaliable during the month, is there any way i can do that by API? Thank you!
hello all,This may be a silly question!I am moving one of our site from Aruba to WLC9800. Our internal ssid's are using EAP-TLS and using internal CA. I have configured everything needed I think. My question is how do I test if my internal ssid's are...
How can I check the RP port status on the WLC 9800-L-F controller? I can use the command below on the 9800-40 WLC and it shows whether there is an active link on the RP port, how can I do the same for the 9800-L-F controller?sh platform hardware slo...
