Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 17 , 2026 through Tuesday August 31, 2026. Our experts Saikat Nandy and Prashanth Bargur Hanumantharayappa will be waiting to assist you and resol...
Hi, We have our main office with WLC setup for 9 AP's. I would like to link/connect a remote AP in a branch office instead of local. Connectivity for both are ok via MPLS. Both WLC can ping remote AP and remote Ap can ping main office WLC. So far her...
Beginning of Crash File: mwar_dump2.crash-------------------------------------------------------- Dumping registers CPU Registers:$ 0 : 00000000 1000cce1 3aaa07b0 00000000$ 4 : 3aaa07e2 00000000 00000002 3aaa07e2$ 8 : 00000000 00000000 000f87bb 0000b...
Can someone point me to a list of IOS CLI lightweight access point commands. Thanks
Hii Everyone, The WAP 121 the clients are connected but the LAN connectivity is disconnected.I have tried everything including resetting the device but still the issue remains the same. please help me in resolving the...
Can somebody help with given below error? I have already upgraded my access point with new firmware. deauthed from BSSID reason 3: STA is leaving IBSS or ESS
I run a large WPA2 Enterprise secured wifi environemnt with a radius authentication back-end. After yesterday's Windows 10 November update, we're seeing increased reports of inability to connect to these SSIDs. Is anyone else seeing this type of use...
Hello all I recently bought an access point Aironet 702i (700 series) but when I start the device. I got a green / amber / red blinking without stop. I tried to reset the device by : • holding the mode button • unplug / re-plug the device • wait for ...
Dear All, I am have problem in subject issue. The Authentication with Active Directroy was workin fine and all of a sudden it has stopped. Now its not authenticating new users to Cisco WLC 2504 through Active Directory Windows Server 2008r2 Standard....
Dear All, I am have problem in subject issue. The Authentication with Active Directroy was workin fine and all of a sudden it has stopped. Now its not authenticating new users to Cisco WLC 2504 through Active Directory Windows Server 2008r2 Standard....
Hi, On a IR829, I have two sim slots. I'm trying to enbale both sim at the same time in order to have two networks, which then will be associated each to a dedicated vlan. Is it possible ? I've seen something about multple PDN and multihoming on the ...
Hi, I'm new to the world of Cisco and routing and am trying to set up a 1841 as a 3G device. I have a working sim card but my cellular interface is flapping.. I think it has something to do with the cell profile but could use some help, thanks. Below...
Hi Experts, We are having 2504 WLC with 7.4.121.0 code and FUS code of 1.0.0 . We would like to upgrade the code to 8.0.120.0 , and in recommedations i have seen that we need to upgrade the FUS code to 1.9( 1.0.20) . Can I upgrade the FUS code direct...
Hi, I need to configure the 5500 series wireless controller please give the best practiced advice (configuration of vlan,ssid ,about DHCP option etc ).and also switch configuration
Hello, I'm having a problem with the bounjor protocol in a LAN but only from the wireless AP(AIR-SAP702i). On the wired network, everything is ok. I've enabled IGMP snooping but no lock.The router i'm using is a 889G-LTE.There is only one VLAN. Any i...
My client has recently moved one of their branch offices from the WAN to a site 2 site VPN setup between an ASA5525 and ASA5506. All traffic from the branch office goes over the VPN tunnel. After the move to the VPN the APs keep flapping with the fo...
