Welcome to the Cisco Community Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, September 14, 2026 through Monday, September 28, 2026. Our experts Shree Hari AB and Suman Sinha wi...
I have a Lenovo T430 with a Lenovo Intel(R) Centrino(R) Wireless-N 2200.Can I replace the Lenovo Intel(R) Centrino(R) Wireless-N 2200 chipset/ module with a Lenovo Intel® Centrino Advanced-N 6235? If not a 6235, anything above a 6205 Available?...
I have 4 5508 WLCs in my environment now, installed at various locations. One 5508 is acting as an anchor for guest access. All other 5508s connect back to the anchor for the same SSID, the guest wireless WLAN. A new office is opening up with sever...
Good Evening All, Need some help ? Problem: Data centre has a Cisco 8500 Series Wireless LAN Controller where all access points are managed (this include all the branch Access points - AIR-CAP1702I-E-K9)The connection from controller differ via var...
Dear Technical Professionals, We deployed a WLC 5508 with 50 AP registered license. Working absolutely fine.We have TACACS server & all devices are accessible via TACACS. Now I want to move my WLC from local ID to TACACS authentication.Can anybody g...
Hello everyone I hope you are fine ...I had two quotations the first is about how to put a rule for accessing services using authentication methods such as Hotspot for access internet as an example ( I want to knew the others for applying them in a...
hi i want to use acces point air sap1602i e k9 first times i need default ip adress to setupit is possible if not give me please solution
We are currently running the Wireless Control System (WCS )on Windows 2003 Server. We would link upgrade the Server OS to a newer version Win 2012. Kindly, advice if it is supported or no .if yes , what is the procedures for upgrading .regards ,
Hi, Is is possible to convert bulk number of APs from Autonomous to LWAPP simultaneously and what would be the template? Kamlesh
Hi, I have dhcp problem with our new AP:I add an AP to our LAN.I make a simple configuration with a WPA authenticate.I can connect some equipment to this AP and our DHCP give an address correctly.We use adptator to give wireless connection to old sta...
Hi, I deployed wireless for one of my clients. All services and the internet are working fine.Only problem is that while sending and receiving emails using Microsoft Outlook, there is a huge delay.Even mails as small as 10-15 KB takes a lot of time t...
Hello,I have a switch (SF300-48P 48-port 10/100 PoE Managed Switch w/Gig Uplinks) and I want to buy some APs (Cisco AIR-CAP3702i-A-K9) and a Wireless Controller (Cisco 2504 Wireless Controller). Is that working?Someone told me that I can use APs and ...
Saludos. Tengo dos Router (No 1) Cisco RV110W. Uno funciona como DHCP y comunica a la red local con el ISP. El otro Router (No 2) RV110W solo integra la conexión de dos impresoras alámbricas a la red wifi local. Por lo que los dos router fueron c...
Does the 3702 , 2702 and 1702 support full functionality in Autonomous mode? i know there was a limited Site Survey function but wondering if they have added full function for these APs?
Dear Team, I have 2 nos of Cisco 2504 WLC configured with 1 SSID each configured with different network address in same LAN. Cisco 2504 is connected to Cisco 2960 L2 switch--->Cisco 3850 L3 switch----->Cisco ASA firewalll--->Cisco 2951 router----> in...
I'm sure this has something to do the RAM or Flash memory. This is an access point that's been sitting on the shelf and as far as I knew it was working. However, I can enter privileged mode but there is no "conf t" or configure terminal option. I ...
