Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Resolved! MSE platform status check up not working
Hi!!I have a problem when using the MSE.I have it installed on a Virtual Machine on a Windows 2003 Server.When i log in and do the:etc/init.d/msed statusit loads a lil bit and then showsStarting MSE Platform, Waiting to check the Status.like 10 times...
We are having issues with VoIP, using Microsoft Lync, over wireless. We are experiencing static, jitter, dead air, and dropped words during calls. We have a Cisco wireless infrastructure consisting of a 5508 controller and 2602 access points. We'r...
Hi, I recently bought 15 new AP Aironet 3500 (AIR-CAP3502I-A-K9) and connect to 3 different Cisco Catalyst 2960S. All of these get powered at boot with 15.4 Watt but after the boot process, they all drop to 14.5W and the LED blinking all color to say...
HiI had 1 end of life WLC 4402 controller. Can it support AIR-CAP1602E-S-K9 access point? If cannot, what is the supported access points for WLC 4402.Thanks
Hi,In one of our factory, there are handheld scanning devices which work over wireless to move data over to end servers.The setup has two-5508 WLC in HA mode, about few 1500 series & 3500 series AP's.handheld device is assigned an ip address & connec...
Hi,I have a 4402 WLC with 44 Cisco Aironet 1240 AP's in lightweight mode and my wireless networks WIFI-GUEST, WIFI-PROV and WIFI-CORP01 works propertly. Recently we installed an Aironet 1600 Series in standalone mode and we can connect to WIFI-GUEST...
Hi all,I don't know if this question has been aswered before, I started few search with no result.My question is, if I have one 5508 with additional licenses (i.e. 5508 with 100 initial licenses, and 50 additional licenses via e-delivery) and it goes...
Hello All,Good App installed on Apple IPAD cannot not sync emails when connected to wireless network at the site.we are using cisco does it required any additional configuration on wlc to allow communication.please advice.Thanks in Advance.
Resolved! Wireless AP H-Reap vlan mapping changes.
Our Wireless AP is AIR-CAP3502E-C-K9 with WLC 5500. The issue is that in H-REAP VLAN Mapping the VLAn ID suddenly changes and if I checl the logs I see no downtime on the AP. Please note that this happen to random AP's and sometimes all the AP's in c...
I'm trying to upgrade our NCS infrastructure from 1.3 to 2.0. I received an error during the upgrade that I needed to increase the number of CPU's, RAM, and disk. I was able to add the additional CPU, RAM, and disk. Going through the upgrade again...
Hello guys,i try to build an RF Group between WISM1 ( 7.0.230 Code ) and a WLC 2504 ( 7.4.121.0 Code )From theoretical side should it be possible, dont it ?How much time should it take ? Every WLC has Group-Mode "Auto"How can i troubleshoot it ?The W...
Hello everyone, I am having issue with one of 1252AG when trying to upgrade from 124-25d-JA1 to 152-2.JA1 with web GUI (IE 11 and Chrome) and TFTP while mode. However, none of them would not upgrade. But odd, second 1252AG did upgraded to 152-2.JA1 a...
Hello,We have an AP at a remote site and it is configured in flexconnect mode. We also have a s Mb WAN link between both sites and have configured QoS. How does the AP mark its CAPWAP traffic and how much traffic is normally generated per one AP in f...
I received a PAK and I generated a license from it. E Mail that I received shows this: Product Name : L-PILMS42-50-M Product Description : Prime Infrastructure LMS 4.2 - 50 Device Upgrade Lic ...
I have two 2602i that are no longer booting after they joined the controller and pulled the updated image. from the console this is what I see during the boot process.IOS Bootloader - Starting system.flash is writableFLASH CHIP: Numonyx Mirrorbit (0...
