Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 17 , 2026 through Tuesday August 31, 2026. Our experts Saikat Nandy and Prashanth Bargur Hanumantharayappa will be waiting to assist you and resol...
Does Cisco still support Bridge APs. Like long range once, I do know that all APs can be set to be a bridge, but with regards to range, it is just a few meters.Also, not interested in Mesh deployments since speed can be a bummer on this kind of deplo...
Hello everyone!I have got Cisco WLC 2504, current version is 7.6.120.0, so I have got an virtual interface on this WLC for mobile users (SSID: MOBILE).I have applyed ACL on this interface "ACL-BLOCK-LAN-IG-MOBILE", so this ACL blocks all traffic to L...
Dear what are the best tools for monitoring, vulnerability test, testing WLAN over Voip, etc. for wireless networks either hardware or software? BestRegard
Hey guys,I updated the software to version 8.0.110.0 for the WLC 2504 two days ago, it worked fine until this morning that it crashed, it's was blinking amber and green and the SYS light as well, I couldn't ping it, then I took the power cable off, a...
The 7.5 release advertises the ability to configure a timeout value so that guest clients which go to sleep are not re-prompted for web-auth. Does anyone know if 7.5 would only be required on the anchor WLC or must it also be on t...
Is there a way to set an idle timeout value on Autonomous Access Points? I have been researching and I see it is possible to do this on a WLC using Lightweights but the only timeouts I can find regarding Autonomous are Session/Holdoff and Re-authenti...
Hello Guys, I have some AirTight APs, SS-300AT-C-60, which are working standalone as WIPS. Those devices can work as AP too butI was wondering if a Cisco WLC can support it. I mean, is there any way to manage these AirTight devices via CAPWAP using a...
Hi guys, I've managed to 'upgrade' the onboard 802 AP to lightweight in error but cannot find a way to 'downgrade' it back to autonomous mode. I've read various threads but none of then work for me. Any advice would be welcome. Thanks Robbie.
Hi everyone, We have a Cisco wlc 5508 (with 50 LAP) running perfectly until yesterday when the wlc suddently stopped working completly.When we reboot the wlc, only ps1/ps2 led are on (alm led is off).We tried to reset the wlc but the wlc is unreachab...
Hi all, I am having trouble getting a 1532E outdoor accesspoint to show up in prime infrastructure. The AP joins the controller, but won't show up in prime.It is a lightweight accesspoint.Prime version is 2.2Controller IOS is 7.6.130.0 Does anyone kn...
Hi,I have strange issue with some 1532 APs. Periodically (approximately after one week) the 802.11a radio interface goes to operational state down.This happens by no obvious reason.It comes back up after an Admin status enable/disable, but I would li...
i have a problem with a 2602e access point that he wouldn't join the controller (wlc 8510)i gave him the image --> p3g2-k9w8-tar.152-2.JB.tarwe have a lot of capwap ap's but ive never had this problem before*Jul 19 07:53:59.999: %DTLS-5-SEND_ALERT: S...
Hello,I have a 4402 WLC running version 7.0.251.2 and a WCS running version 7.0.164.0.I was hoping to upgrade the WCS to version 7.0.240.0 but wasnt sure if it was compatible, the only document I can find is attached below, it says though '2500 serie...
In Cisco download page we can find AP IOS images (w7) and LAP images (w8) so we assume there is a possibility to downgrade one 1520 in LAP mode to Autonomous with the traditional procedure (renaming IOS to default).But I have seen a comment in a post...
Hello everyone, Hoping someone can assist me, I am trying to locate where to download the cisco aironet desktop utility version 4.5. I found some technical documentation here. http://www.cisco.com/c/en/us/td/docs/wireless/wlan_adapter/cb21ag/a...
