Hi, I'm planning a new wireless deployment and want to use these 2 antennas: AIR-ANT2588P4M-NSAIR-ANT2513P4M-NS Both have a higher gain then 6 dBi and from what I understooth and Cisco documentation I need to use the 9120AXP AP.Now i'm confused on wh...
Forum Posts
Valide que se puede integrar INTU con Cisco ISE, es posible integrar la solución de MDM Intu con Cisco pero sin un ISE de por medio sino directamente con una WLC 9800?
Hello Everyone,I am encountering an issue with one of our access points and would appreciate your insights or guidance on the matter.When navigating to the Wireless > Access Points dashboard, I noticed that the connectivity to UTC is indicated by red...
Hi,This links here gives Access Denied because of Policy violation: https://community.cisco.com/t5/wireless-mobility-knowledge-base/how-to-install-windows-drivers-for-the-aironet-client-adapter/ta-p/3132537 Please supply Cisco Aironet 350 (FreeDOS, M...
Do Cisco Wi-Fi 7 and 6E APs support Zigbee? The datasheets don't mention the Zigbee support but few of the Cisco forums say that Zigbee support can be enabled. So, I'm a little confused.Sharing a similar post that raised doubts adding to my confusion...
Hello Team,We recently encountered an issue where an access point at a site was automatically switched to Wireless LAN Controller (WLC) mode. As a result, all other access points at the site joined the AP that had been converted to a WLC, instead of ...
Hi Team, I am deploying Cisco mobility using a cisco AIR-AP2802I-S-K9 as the master AP (running as controller ). Initially my AP is running at CAPWAP 8.3.143.0 image that is why i did not upgrade the image image. The only upgrade i did is to the mob...
I have seen on few Access Points that the AP reloads with reason: Image upgrade. Post checking the logs in Prime I can the below message in event log :"'802.11a/n/ac' interface of AP ' TEST-AP12'associated to controller 'TEST-S8-WLC1(10.128.50.41)' i...
Resolved! Wi-Fi 7 APs now available
- FYI : https://documentation.meraki.com/MR/MR_Overview_and_Specifications/CW9178_Datasheet https://documentation.meraki.com/MR/MR_Overview_and_Specifications/CW9176I_%2F%2F_CW9176D1_Datasheet M.
We are using the SSID tunnelling and L3 roaming to MX250 as the wireless concentrator. I want to move this SSID tunneling and L3 roaming to the vMX on AWS. Does vMX support this setup and how to configure it?Thank you.
I have few APs joined the C9800 WLC. The WLC is running on firmware version 17.9.3. Regulatory domain is set as MX for Mexico. But the operational status does not come up.
Resolved! converting C9130AXI into EWC
I am currently trying to convert a C9130AXI into EWC I have done a factory reset using 30 sec push of factory reset button see belowWait for the button to be released ....Button pressed for 36 secondsSetting env for full reset..Writing to Nand... do...
We use scanners in our company that can be wireless, our Meraki wireless is configured with Nat Mode"Clients receive IP addresses in an isolated 10.0.0.0/8 network. Clients cannot communicate with each other, but they may communicate with devices on ...
Hi community, I have a pair of WLC 9800 in HA mode. The management interface labelled SP on the standby WLC is down, lights out even though it is configured the same as the SP port on the primary (different IP). Is this normal behaviour?
I am using 9800 wireless controller with C9120AXI wireless AP. When I connect to wireless SSID from a device via EAP-TLS, EAP-PEAP, it will connect successfully with TLS 1.2 protocol. When I connect to wireless SSID from a device via EAP-FAST, it alw...
