Hey Community! I'm excited to share something we've been working on that I think will really resonate with many of you managing wireless networks today. We just released the Cisco State of Wireless Report 2026, based on insights from over 6,000 wirel...
Forum Posts
Hi folks,Running a Catalyst 9800-40 WLC. 1463 WAP's connected, predominantly C9136I WAP's. 8,817 active clients with 4,796 clients on our SSID using PEAP authentication via ISE on the back end. We are observing clients will frequently disconnect fro...
Resolved! Machine auth on SSID
Looking to only allow domain joined machines on a SSID. Was looking at radius auth but that seems to only check mac address or user accounts despite this statement in the config doc:"Type or find the Domain Users group. This group should be located i...
I have already activated user profiling and I see the Device Type.Does anyone know if it is possible to block access to a certain WLAN based on device-type?I have a WLAN where only Smartphones (Android or iPhone) should be able to connect.Thanks
Hello!I have a customer being told by a competitor WiFi manufacturer that there is an AP limit with Meraki. There are customers with 10s of thousands of active APs, and so I was wondering if there is perhaps a limit of APs within particular Meraki "n...
We are implimenting a OPSWAT NAC to secure our wired and wireless network (Wireless moving from Windows RADUIS)We have set up a test SSID and have been able to authorise clients sucessfully and they get the assigned vlan in the group policy assigned....
The AP boots up - I connect a console cable and I can see the logo of u-boot and then weird characters. Image broken? That was running an EWC image without problems, rebooted it one day and that's it...What's interesting, I can see (using CDP) that a...
My Current scenario is Wireless controller > Anchor Controller > Radiuswe are in the process of changing the RADIUS serverIn current setup traffic flows as WC>Anchor>RADIUSBut when I change the IP of RADIUS to new RADIUS server, it goes WC>RADIUS, do...
I am utilizing Clearpass Guest with Meraki (using the Cisco Identity Services Engine (ISE) Authentication Splash Page option).The functionality works as expected. Users authenticate to Clearpass and I see the appropriate Group Policy assigned in the ...
Hello Everyone!I'm trying to configure a pair of 9120AXE into a bridge and after some reboot (changing the ap from capwap to workgroup, back to CAPWAP, then eWc, up grading the image, etc) it seem that the access points are always end up glitching on...
9800L-F running 17.12.02 in the Corp Data center. Large WAN sites connected via Cisco 8x00 SD-WAN devices. Small sites have S2S VPN connection to the corp datacenter using 3rd party Firewall. All remote sites APs are Flexconnected and registered t...
I've reset Cisco AP 9130AXE which was in EWC mode and now CLI shows some unusual languages.j▒ĥk9▒9')▒▒9▒▒▒1/▒▒▒((I▒!q▒99▒H!▒7 H▒01w((I▒▒!▒1▒▒▒91▒91▒ ܖ▒H((Z((▒▒▒1▒H9▒▒▒1▒▒19▒ň1▒▒7▒▒79▒▒79▒▒H▒yI▒!)▒▒▒1▒)ͥy▒H▒▒▒!q9▒!9{穵9!!▒▒11▒(▒▒)▒▒▒9▒▒▒▒▒▒▒▒▒▒▒!▒▒!{q!...
Dear Team,I am currently using the Wi-Fi Mobility Express model AIR-AP1815I-I-K9, with WPA2 Personal authentication and MAC filtering enabled.Is there any way to track the traffic consumption for each MAC address on a daily or weekly basis?Thanks in ...
After configuration Cisco C9130AXE-D access point in EWC type, both Radio 5 and 2.4 shows operationally down.SSID is not broadcasting.
I am trying to learn wireless by using two Cisco 2504 WLCs. The issue that I have with these WLCs is that I can't negate a configuration. When I am asking AIs about this issue, they all say to use no before the command. I guess AIs are too young to k...
Hi all, apperiacte your help. I have 1 ME wlc model 3800 and 2 AP model 2800 associated with wlc. I have the firmware for both model. I've tried upgrading through http (gui), uploading the wlc firmware (3800) file first. Wlc automatically upload the ...
