Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Hi everyone,We need WiFi security on our corporate SSIDs locked down using certificates, we are using wlc cisco 2100 series. We need these on every workstation, laptops etc. Need help guys.Kind regards,Norman.
Hi,I have an access point running 15.5.2(JA). I can't do a hard reset, well the guy that is with it can't, the access port is a long way away and it won't let me delete the config. I've never set one of these up before and pushed for time. We don't ...
hi there,Can anyone recommend a directional antenna for the WAP200e.I've been googling but can't seem to find a product. I have found omni-directional but no directional antennaeThanks for any help with this.A
Just inserted a new 5508 WLC into the network. We current have 3 4404 WLCs, and there was a need to duplicate, as much as possible, the configurations on the 4404s, and the design. The 5508 came online as expected. We moved a few access points over t...
Resolved! Certificate Question.
Hi,We have a 5500 controller with one of the WLANS using 802.1X authentication.We are going to revoke the certificate (retiring the CA) and want to use a different cert.Do I specify the cert in the Controller Admin page or only in the Network Policy ...
Hi AllIs there a yagi that I can use to provide 11N coverage within some racking in a large warehouse under the 5GHz band. I understand there is one for the 2.4GHz.ThanksSimon
Dear Folks, I do have 1131 LWAPP in home, i was wondering if i can convert to Autonomous . I read in the documentation, that only way is to use with controller. Is it true ? or can i convert without connecting to WLC . SID
Resolved! Repeater ssh/web configuration interface not reachable after performing antenna-alignment scan
Hello, we have a couple of AP1262N-E-K9 APs with firmware version 12.4(25d)JA1 operating in autonmous mode. One AP is setup as repeater while all others are in root mode. The repeater has setup one parent MAC address so it associates every time to th...
Hello,We implemented WLC 5508 software version 7.3, with 8 Aironet devices, most of them are AIR-LAP1131AG-E-K9, and two AIR-LAP1242AG-E-K9.I could really have benefits of VLAN select feature, but I noticed that it's not working like it should. Two i...
Hi Guys,I have few APs showing "RED" in NCS map but when I click on them I can see they're associated to a controller and clients are associated to them as well.Also when I logged into the controller itself and run the command : SHOW CLIENTS SUMMARY ...
Hi All,and i'm here by want to ask something about wireless that our team developed currently. i'm using WLC AIR-CT5508-K9 software version 7.3.101.0, ISE, cisco prime infrastructure 1.2 (1.2.1.012), and using Odyssey access client manager..all runni...
hi all,I was wondering whether anyone has experienced the following symptoms on Reporting.WCS Rogue AP reports do not run and show up as 'Expired'this does not occur to all the Rouge AP reports though (they are being created based on floor areas; on...
We have cisco wlc 2125 with 13 AP 1131g. All works good. But after power failure one AP can not join to controller, only reset help to recover connection AP to WLC. Additionally, we don't have access to rs-232 port on AP. In this moment on WLC we can...
Hi team,We need to use this workgroup command in AIR-AP1242AG. This AP comes with the default IOS c1240-k9w7-mx.124-21a.JA1, but this does not support the command.I tested too with IOS c1240-k9w7-tar.124-25d.JA2 without success. Any of you knows abou...
hi We currently have created a wireless SSID to accomodate about 1024 users . We are expecting more load on the wireless infrastructure with more devices connecting to it ( more laptops and Iphone devices are being rolled out).Is it better to increas...
