Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
According to what I've read I'm supposed to be able to search the iTunes store for Cisco Mobile 8.1 (for the iPhone/iPad), but all I'm turning up with is version 8.0. Am I missing the obvious?Thanks,-Mike
Hi, We have few WAP 200 Cisco wireless access point and using it in security mode enterprise and Access point mode. But some of users are facing diconnectivity in between. When we will restart the device then they will be able to connect again. Could...
Hello,the is one issue i see in the Log of the AP when the user report frequent disconnect of the wifi on his laptop.*Nov 30 04:34:50.176: %DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating Station 0026.b6ee.9406 Reason: Sending statio...
Hi everybody,i want to verify whether the controller below can control all the 11 access point or do i need to get a LAP access points?AP541N-E-K9Dual Band Single Radio Clustering Access Point, E(ETSI)11AP540N-CMKAP 540 series Ceil...
When we attempt to reach the WCS we receive this message occassionally,Service Temporarily UnavailableThe server is temporarily unable to service your request due to maintenance downtime or capacity problems. Please try again later.Apache Server at ...
Hello Everyone, I have the below problem with configuration described below.The project is actually ready, we have configured basic routing.Please helpDescripion: There is an ASR1006 Router in the network that serves as an Intelligent Service Gateway...
Hi all,Recently We have renew the service contract for WS-SVC-IDS2-BUN-K9 module.Problem description:For one of our customer we have provide 24x7x4 partner support for Cisco 6509 chassis and WS-SVC-IDS2-BUN-K9 module which is present in the same cha...
Hi Guys,Another one for you all - we have several offices running seperate WLAN controllers various models and software versions. We have the same SSID in each office. We dont use WCS/NCS as yet. We are using MS NPS Radius/PEAP/MSCHAPv2 for authentic...
I am having an issue with a 1310 in root bridge with wireless clients mode. I have the bridge connected to another bridge in non-root bridge mode and everything is working fine on that end on ethernet.My issue is the wireless one the frirst bridge....
Resolved! WLC 2106 Guest Wireless Access Problem
We have a 2106 that was configured by a former employee. No one left in the company is qualified to configure it. The wireless guest access used to work fine. We'd configure a guest user account. They would connect to the guest wireless, open a w...
We have approximately 150 1142 LWAPP's deployed in our facility. Recently we started getting complaints about speed issues (90% are using G 10% N). Upon investigating we found that the speeds are flucuating rapidly. Everything from 54Mbps down to 1Mb...
This is an unusual situation:I have the need to run a few autonomous APs (1262) for some sites on satellite links. At a bare minimum I need to run two WLANs. One is wide open, and the other with an ACL that heavily restricts access. Is there any way ...
Hiany help with reloads of aps joined to wlc 2504 7.3 with this log messages*Dec 3 16:30:47.575: %SYS-5-RELOAD: Reload requested by LWAPP CLIENT. Reload Reason: LSC Provision max retries.*Dec 3 16:30:47.575: %LWAPP-5-CHANGED: CAPWAP changed state t...
I have been trying to manually disable clients from within WCS by calling up the client in 'Monitor Client' and then in previous versions you used to be able to select 'Disable Client' from the drop down list. This would take you to the template page...
I am using 2 anchor controllers 5508 as DHCP server. Anchor controller A is primary and anchor controller B is secondary. From time to time, client will complain "duplicate IP address error" when they try to connect guest wireless.First question: bot...
