Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Hi everybody, I have some old 1231 APs in the school in which I work.I would like to create a local network (no LAN, no internet, just a point to point wifi connection) managed by the access point (in DHCP).That's because we have an apple TV connecte...
Resolved! SSID Disappear
Hello People,I configured my WLAN to work with 8 SSIDs, in the beginning it was working well but now some SSIDs are't showing after i put one more.The broadcast is enable.I reconfigured the SSIDS, i rebooted the controller and APs but the problem con...
Hello board,I installed two MSE-virtual appliances in HA mode, using one interface on each MSE (eth0).Version: 7.2.110.0After initial installation, I added the MSEs to NCS and everything worked perfectly.Now for the HA case: The link to the 2nd MSE w...
I am seeing a lot of client has joined profile XXX in the logs, and the customer has been saying the PC's are dropping constantly and take up to 5 minutes to reconnect. I found a lot of Auth flood signiture hits, and disabled the signature as a temp ...
Resolved! Guest Users - Web Auth
Hello,I need to know about one case using web authentication with guest users.I have a environment where when i created the user in NCS using the looby account the user can authenticantee many times during a period but in a lot of machines at same ti...
Hi All,I have a large wireless network over my WAN with many WLC and LWAP's. Few days back i met a problem with LWAP's. we can c them on controller and we can login but none of the clients are getting assocated. If we reboot hte LWAP,clients are gett...
Hi I am getting little confuse about the configuration of my second WLC .I have a project going on with main office and 10 sites . I have placed my primary WLC 5508 with software 6.0 and all the branches i deployedap . I put all the AP in Hreap mode...
Hi,I would like to be able to allow a specific client to only associate at 6mbit/s -is this possible using the wlc controller 5508?another option would be to limit a whole wlan ssid to 6mbit/s but i can't find a way to do that either.Other wlan ssid'...
Hello Everyone,1 . I tried to login via root to NCS linux server but couldnt get success.is anyone have an idea ???2 . I want to take automatci backup of NCS server to a remote PC, how can i do by command line via ssh ??Reagrds
Hello.We have a 5 storey building.My question: Is a good idea to install one Aironet 3500 or 3600 series AP with multiple external antennas and to place each antena on every storey ?Maximum number of wireless clients will be ~200.You can see the desc...
Hello all,In WCS by default the lobby ambassador has option to generate manual or auto (random) password for guest user account. Is there any way that we can restrict lobby ambassador to generate manual password for guest user ?Regards,Anis
Resolved! 3600/3502 login authentication
All,Can we enable ssh on 3500 /3600 APs along with use radius for login authentication?idea here is to that ssh will provide another method to access the AP for troubleshooting purposes.I know with autonomous mode APs this should not be an issue bu...
Hi everyone,I have a setup of 5 non-root bridges going to a root bridge. We setup a second root bridge on the same pole for redundancy (same config, minus hostname and ip address)I split up the non-roots, so that the two important ones would go to ro...
Resolved! WLC 5508 - WLANs disabled after reboot
Hi, I'm running 3 WLC 5508, 2 of them running image AIR-CT5500-K9-7-0-116-0.aes, one AIR-CT5500-LDPE-K9-7-0-116-0.aes. On the 5508 running the LDPE-image, I have 9 WLANs (170,171,180,181,190,191,281,282,283), all defined with admin status "ENABLED".W...
Just did a dot11 radio link test on a point to multipoint 1400 series bridges. Can someone tell me how to read the results of the test?
