Wireless

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

review


Labels

Forum Posts

Hi Team,One of my customer has an Apple IPAD 2.The IPAD is getting registerd through Cisco WLC 7.2. The APs that are being used is AP 1252 & AP 1242. The AP are configured in flex mode. The issue that we are facing is all the laptops and IPADs other ...

charu.kamat by • Community Member
  • 889 Views
  • 1 replies
  • 0 Helpful votes

HiI know that very few people have their wireless controllers on version 7.4.100. But has any one noticed that the NAT IP address field in the management interface configuration menu is missing?, although it is mentioned as being present in the WLC 7...

grabonlee by • Level 9
  • 1987 Views
  • 4 replies
  • 0 Helpful votes

In WCS you could sort ascending and descending in the AP Uptime and CAPWAP Uptime dashlets.In Prime Infrastructure you cant change the sort order, it is always descending. I think it is much more useful to see which AP that has rebooted last than to ...

s.hellman by • Level 4
  • 587 Views
  • 0 replies
  • 0 Helpful votes

Good time of day.I have a problem with MSE client traking.I havePI 1.3 (1.3.0.20) MSE Virtual Appliance v 7.4.100.0Controller AIR-CT2504-K9 Software Version 7.3.112.0Three access point AIR-LAP1261N-E-K9 IOS Version 15.2(2)JA1$Licences for PI and MSE ...

BigWoop111 by • Community Member
  • 808 Views
  • 0 replies
  • 0 Helpful votes

I am conducting some inside site surveys, I have a lot of documentation on doing a survey and have good equipment but one question I have is what should be the minimum signal strength or quality that I want to look for? For example I am thinking that...

vosm by • Level 1
  • 1616 Views
  • 4 replies
  • 0 Helpful votes

Hi All,I am new in this field. I had saw some information and I can catch the basic meaning of wireless LAN. But I can not find any information about the detail workflow when doing site survey and how to work when an AP doing as site survey client, a...

teru-lei by • Level 5
  • 1362 Views
  • 3 replies
  • 0 Helpful votes

                   I have an access point that is pretty much unresponsive. The LEDs show Radio=Green, Ethernet=Red and Status=off. Serial cable to console port using hyperterminal shows nothing on the boot. Any help with this is much appreciated.

johnbouman by • Community Member
  • 2763 Views
  • 5 replies
  • 0 Helpful votes

I have ordered an additional 5 licenses for a 2504 wlc. I also registered it with Pak key all worked fine but i can not get it to work.When i upload it from tftp it tells me it that it is allready installed. I have then tried to activate the eval lic...

huber by • Level 2
  • 2262 Views
  • 5 replies
  • 0 Helpful votes

In many Cisco document, they mention SKC is also known as PKC. But I don't think it is correct:http://www.cisco.com/en/US/docs/wireless/controller/7.4/configuration/guides/wlan/config_wlan_chapter_01101.htmlhttp://www.cisco.com/en/US/docs/wireless/co...

zhenningx by • Level 8
  • 991 Views
  • 2 replies
  • 0 Helpful votes

Hello,Does anyone know the OID to retrieve the RSSI from a Cisco 819 3G router?  I've just run a MIB walk using Solarwinds MIB walker and it doens't seem to find anyting relating to RSSI, but brings back thousands of other OID info.Thanks

I want to create an SSID that will only allow teachers to authenticate at my school.  Is this possible using ACS?  In other words can ACS allow only certain groups in AD access to a particular SSID or subnet?Thanks for any suggestions.

tdaly by • Community Member
  • 1613 Views
  • 4 replies
  • 0 Helpful votes

Hello Community,if a question regarding the WCS:How can i see which MAC-Filter Entries are not used anymore. Because i have around 2000 Entries but only 1900 Users Really thanks for helpKind regardsPhilip

Philip91 by • Level 3
  • 675 Views
  • 1 replies
  • 0 Helpful votes
Review Cisco Networking for a $25 gift card