Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Hi Expertsany AS Image on CCO for the Cisco AP 1260,if so how to download it to the flash of the ap then boot properly the new code for standalone? thing is that have one with lwap enable so that i cant do any thing ,upon booting it looks for control...
Is there a command that when entered into a Dell switch which will list all MAC's and corresponding ports which they are plugged into? I only know of typing 'show bridge address-table ethernet e*.' which requires you to go to every port in the switch...
HiI have 5508 WLC (Running 7.2) in seperate buildings. I have created ACL's on both Controllers and the only thing that is failing is the Mobility Control Function. The ACL on WLC B is the Exactly the same except with some IP's being reversed. I have...
I have a ISR 2811 with NME-AIR-WLC6-K9 WLAN controller. I have problem booting the WLAN controller. When I try to have an access to the module (service-module Integrated-service-engine 1/0 session), it keep rebooting with the message : Booting from ...
Could someone recommend a good book for deploying WLCs?
HiIf I'm reading correctly Load Balancing is not advisable if using voice of wifi.On a conroler with 70.220 - Wireless - Advanced - Load balancing Load balancing - client windows is default 5, max denial 3But on the wlan, the load balancing ...
we have a number of remote branch offices with HREAP access points. Each office has an MPLS link back to the main office where the WLC's are. We have IP SLA setup on the switch so that when the MPLS link goes down, a VPN tunnel is built over the in...
Hey I have a Question i am testing mobility group with Failover for redundend connection between 2 Cisco 5500 Wlc.On both the controllers i got the mobility working And both the controllers have the same version And configuration. But when i unplug ...
Is there away to configure ACS 4.2 to only allow certain EAP-type of authentication per SSID? For example: SSIDA - only allows EAP-TLS and SSIDB - only allows EAP-PEAP on the same ACS server?Any help is greatly appreciated.Sent from Cisco Technical...
A 4402 Controller (Software Version - 7.0.98.0) with Web-auth via LDAP database works fine for a random time, two days, some hours.The LDAP in controller is configured with a user, that has bind's privilegies.I don't know why the authentication of us...
Resolved! WPA2 key change question
Hey guys, I am trying to change wpa2 key on an Aironet 1231g access point. Once I change they key, clients cannot authenticate to the access point unless they either change the password or forget and re add the network on the client device. Is there ...
Hello,I apologize if this has been covered before but I can't seem to find an absolute answer (probably because there isn't one) on how we should configure the switch ports for our 5508 WLC. We have a 5508 WLC with 4 ports plugged into our 3750X Sta...
Hello, I have two Aironet 1310s out doors - one on a boat and the other on a building. I have one ANT24120 antennas attached to each AP. I am trying to determine why I am having dropped connections. Any help would be appreciated.
Dear All,Would like to enquire regarding 2 x WAP4410N access points that we have installed at our site. These devices work fine with the power brick but when conmnected the SG300-28P ports POE lights up, and seems to keep rebooting for some strange ...
Hello, I have two Aironet 1310s outdoors - one on a boat and the other on a building. I have one ANT24120 antennas attached to each AP. I am trying to determine why I am having dropped connections. Any help would be appreciated.
