Internet access available. WLC has HTTP access to the Cisco License Portal. WLC#ping tools.cisco.comType escape sequence to abort.Sending 5, 100-byte ICMP Echos to 173.37.145.8, timeout is 2 seconds:!!!!! How does WLC find SA (Smart Account) and VA (...
Forum Posts
9120 AP continuously repeats Join & Disjoin from 9800 WLC I don't know why rediscovery.someone give me a hint I have done Layer1 check.9800 WLC replacementcable replacementswitch replacementAP replacement Please check the attached txt file [*08/29/20...
I want to use the Air-ap1562i-e-k9 access point in my office garden, I connected it to the router with Cat6 cable (with PoE Injector), when I turn it on (led is red for 5 seconds) and (blinking green for 1 minute) (green, red and yellow) turns) and a...
Hello,I'm inquiring about the location where I should direct my attention to identify any DFS (Dynamic Frequency Selection) events. Our wireless access points are operating on DFS channels, and we've been receiving reports of WiFi disruptions. I have...
as we know, per design new access point will get default tag policy, tag rf, tag site and will not provide wifi.I have N+1 WLCs and its quite inconvenient manually assign tags for new access points and then need not to forget configure such static as...
Hi, Suddenly one of our 1832 stops working. In serial console I get repeatetly output like this GPVTG,,T,,M,,N,,K,N*2C $GPGSA,A,1,,,,,,,,,,,,,,,*1E $GPGGA,,,,,,0,,,,,,,,*66 $GPRMC,,V,,,,,,,,,,N*53 $GPGSV,3,1,12,01,08,240,,03,45,135,,04,62,240,,06,2...
Hi I have performed 'clear config' and 'reset system' commands on two access point CISCO 1850 with same result.After reboot I have done the configuration (administrative account and SSID parameters).But on both AP, after restart, I can login but the ...
Resolved! Roaming Between AP Groups
Hello Dears,I've a question, and appreciate your support.If we roam from AP group 1 to AP group 2 and had to re-associate then would we receive an IP address from AP Group 2? if yes, how could that be performed? wouldn't that go against L3 roaming fe...
Hi,We have some branch offices with Aironet 2700 and 2800 access points and old WLC 2504 running 8.5.151.0. As the WLC 2504 are beyond end of life and support for Aironet 2700 and 2800 has been re-introduced with 17.9.x we migrate our old access poin...
Resolved! WLC 5520/5508 disable 2.4G or 5G in CLI
I'm trying to disable 2.4G/5G for each AP in WLC. Are there any related commands in CLI?
It seems that in order to execute RESTCONF queries against the WLC, a user with admin access (privilege level 15) is required. Is this true? In order to execute read-only get queries against the WLC, you need an admin user?
I am trying to understand why an AIR-CAP2702I-A-K9 remains functional when the VPN tunnel to the WLC is lost but an AIR-CAP3802I-B-K9 does not. They are both connected using Flexconnect to the same CT5508 wireless controller. Both models of APs are i...
Resolved! compatibilty matrex for 9800 wlc
actually we are planning to get new 9800-L , is bellow access points supported by 9800-L Wireless controller , and if it is supported is there any feature and version limitationAIR-CAP3602I-E-K9AIR-CAP3702I-E-K9AIR-CAP3602E-E-K9AIR-CAP2602I-E-K9AIR...
WLC-9800-40Sw: 17.9.3Hello, I have a client issue with a user. He dissconnects very often and a radio trace and clientinfo shows this:Any suggestions what to check ?regardsJohann Folkestad
Hi,I was investigating wifi issue forthe users , they cant get dhcp and noticed some discrepancy in the config , I am not sure if this can cause. Can you help with expert review? So, Wireless/AP/General/IP config dhcp shows 10.2.0.1, mac address of t...
