Hey Community! I'm excited to share something we've been working on that I think will really resonate with many of you managing wireless networks today. We just released the Cisco State of Wireless Report 2026, based on insights from over 6,000 wirel...
Forum Posts
I was asked to provide some information on our WLCs. Two of the commands I was able to figure out on the WLC9800, but the last one "show sysinfo" I can't find anything similar in the command structure.I was wondering if anyone has an idea of what com...
Resolved! AP IP Assignment | Static vs Dynamic
Hello, I understand that the DHCP feature needs to be enabled on the WAPs during the initial deployment process, however, once the WAP has been fully deployed and operational, what is the best practice with respect to the IP assignment on the WAP. Is...
I have a dhcp server that handles ip addressing for our sites. I made a 10.1.72.0/21 subnet. I want this subnet to house all the ips for devices on vlan 72. Locally I was able to achieve that. But I can't figure out how to achieve this from a differe...
The wait is over! 6GHz Standard Power Wi-Fi with Automated Frequency Coordination(AFC) is now GA! Available on all Cisco Meraki Wi-Fi 6E access points on Meraki Dashboard with release version 30.7. Need more info? The set-up guide is here: https://do...
Resolved! MR44 + fortigate
hello everyone,I have connected MR44 access points connected to a cisco switch and this one with an output to the internet through fortigate.I have the following problem... I can not ping between the devices connected by WIFI. the dhcp server is deli...
Resolved! Question for License LIC-ENT-5YR
Hi Team,One of my Customer need this License LIC-ENT-5YR to work with an MR57-HW that will ultimately end up in Bermuda. Will there be any issues registering this license in Bermuda?Please advise.
Hi All, I am planning of using the CW9163E outdoor access point to use indoors with external antenna's to leverage the 6GHz band. This is the only access point that supports both external antennas and 6GHz. However, in the EU it is not yet allowed to...
Hello everyone,I have already opened a case to the support but I want to know if anybody else is facing the same issue.Since last Friday approximately our provisioning scripts (provisioning of networks and SSIDs) keep failing. More precisely they fai...
I have a cisco 1815w, i have enable the lan port, but when i connect a printer ticket, the leds from the printer and ports are flashing, but have not conectivity, and on the controller running 8.10.190, but if i connect another thing like phone, c...
I checked for another post regarding the use of "_" as AP Group name but that is not our case. I am getting multiple error messages likes this after migration this site from a traditional MPLS connection with guaranteed BW to SD-WAN where the remote ...
Any way to convert AIR-AP1852I-K-K9 to C9120AXE in EWC mode.
I upgraded our MR 33 from 25.x to 30.x and clients could not connect.
hello!I have problem with upgrade firm ware. I tried to upgrade using the following commands:ap: format flash:ap: resetap: flash_initap: ether_initap: set IP_ADDR x.x.x.xap: set NETMASK x.x.x.xap: set DEFAULT_ROUTER x.x.x.xap: tftp_initap: tar -xtrac...
Hello, dear Colleagues!I've set up TACACS in WLC 9800 but when I connect from SSH I see the error: WLC9800>enPassword:% Error in authentication.And when I login in GUI I see only two menus - Dashboard and Monitoring. My config: WLC9800#sh run aaa!aaa...
Hello,We have 2 WLC 5520 in HA pair, SSO, today the primary had a failure, and the HA was broken, the APs correctly migrated to the secondary controller, but some APs that were rebooted were not able to join back.The problem was there was no license ...
