Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Dear Cisco Community, I am unable to connect to three separate cisco AP2802i Access points using console port. Note that console cable is working as I am able to use it to access cisco switches. I have also tried to hard reset one device and still no...
Hello Everyone i have an ap Cisco air-ap1832i-e-k9 and it was working fine , i added one more ap and i converted the ap to Mobility Express and i made first ap is a controller and i changed this port to new port but i have an issue with the followin...
Hello everybody, I am a University student, my colleagues and I need to work with Cisco Access Points (embedded and lightweight).We figured out that the first step should be to upgrade the firmware of our AP (it's currently in version 16.12).I seem t...
Greetings,I'm working on setting up an EVE-NG lab and I have 2 different ISO images for versions 8.3.141 and 8.7.102, when I'm doing the initial setup of the 5500 vWLC after I configure the management IP I get the error message saying Error in settin...
Resolved! Cisco AP not broadcasting SSID
Hello everyone!We have configired a virtual WLC with demo license for 200 AP (60 days)Our 2602 AP has joined the controller but it is not broadcasting SSIDs even though the WLAN status is enabled and Broadcast SSID is checkedANy suggestions?
Resolved! C9800-80 ARP Packet Processing
Hi everyone,My user currently RUN state. I capture radioactive trace, user send 2 arp packets to default gateway. One is destination MAC address ffff.ffff.ffff but other one's mac address unicast cisco MAC address (probabbly gateway's mac address). W...
Hi,I am facing an issue on DNAC. I have the need to migrate an SSID from our old controller to the new C9800. This SSID is anchored to an old WLC which is not managed by me.Within DNAC I can only add a mobility peer if it is managed by DNAC (its a dr...
Resolved! Correct Injector
Hi Team, Just asking what is the correct Injector for MR56HW? Inj4 or inj6? Thanks! Mike
Hi, Has anyone encountered this issue on AP 1832i ? software version 8.10.151.0. [*xx/xx/2022 13:52:36.3937] waiting for sending msg to wcp/radio1.set_radio_mode - 4 [*xx/xx/2022 13:52:36.3937] [*xx/xx/2022 13:52:36.3931] waiting for sending msg t...
After an upgrading our standby 9800 to 17.9.4a our DNAC integration appears happy, but when we provision from the UI we get the above warning. I haven't kicked any APs over to the standby pair yet to verify, but has anyone else seen this actually re...
Dear all, Can you please help me how can I configure globally Tx Power Level Assignment to Assignment Method: Global for all connected APs? I neeed to have all APs configured dynamicaly I have on AireOS WLCs a lot of APs where are configured this lev...
Hello Dear Expert I have an issue after the last upgrade of the WLC I have 8 access point cisco that brodcast different SSID : corporate, Guest and public my problem is with the SSID corporate where I have bad BW , the line is a 300 mbps and when I ...
Hello gyus, Can anyone clarify if there is possible clean/wipe the client/visitor data information of the register Portal from CMX (version 10.3)?The end device register on the CMX portal using your name, e-mail and personal identification for exempl...
Resolved! Some Wireless Users are not getting IP
Hi All, I have setup which consists of WLC 9800-40 and catalyst 9136 APs. Some users are able to get the IP address from the DHCP server whereas some users are unable to get the IP Addresses. Please need your suggestions
Hy I am searching for a solution to place Accesspoints on maps in DNA Center. Is there a possibility to configure the "siteHierarchyGraphId" value to a newly provisioned AP? In the course of an hardware lifecylce it would save an big amount of time. ...
