Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 17 , 2026 through Tuesday August 31, 2026. Our experts Saikat Nandy and Prashanth Bargur Hanumantharayappa will be waiting to assist you and resol...
Hello,Here is part of router configuration of dhcp for Wireless AP.Ip dhcp excluded-address 172.16.100.1 172.16.100.100ip dhcp pool lwapp-apnetwork 172.16.100.0 255.255.255.0default router 172.16.100.1option 43 ascii "172.16.1.10"ip dhcp pool client-...
Hello,I read some where that I can pre-position (upload) the new LWAPP or CAPWAP to access points before I upgrade the WLC code. This will reduce the time it takes for the APs to download and run the new code from the WLCI am not able to find a docum...
I recently purchased the E3000 and need a little help. I thought i had read that this devices can act as an access point. There is no clear "access point" mode option so i configured it as best as i could to work with our radius server. I can connect...
Correct me if I am wrong. Option 43 is not necessary for APs, especially when they have static IP or DHCP configured. So in what scenarios is it needed?Thanks, Han
Hello there.I'm about to set up a wireless environment and my question is: can I define 1 Root AP and somehow "sequentially" mash APs, each of these a bit farther away? Like this:Root AP0 --> Mash AP1 --> Mash AP2 (which connects to AP1, because not ...
Hello! we have WLC 5508 (6.0.188.0) and some converted APs AIR-AP1141N-E-K9. Everything works fine except one moment:1 of this converted APs is located beyond the office building, but it is still connected to our local network as if it was located ...
hiI have 5 access points and want to configure channel and its frequencies...what should be the channel frequency and its operating mode so that user would get bestpossible results??I am facing some wifi fluctuation problemsI have set frequency chann...
Hi,I have a small building which has two levels. I have a 1230 on the top floor and about 10 people. Below that floor is another office with 10 people. They don't all use wireless, infact its only used for guests and smartphones, tablets of which the...
Hi all,I've been poking around in ACS 5.x, trying to figure out how to make a Service Selection based on the EAP type the client is using to authenticate. For example, I have a wireless LAN on my WLC and my wireles clients will use one of two EAP typ...
Hi,We had a pen test completed on our wireless network recently and two elements that came out of it that surprised me were the following:The guest wireless portal is using SSLv2 and they recommend that we use SSLv3. I haven't been able to see anywh...
Guys,I have deployed a centralized wireless architecture with 2 x wisms in each of our DCs. I just noticed the clients are receiving incorrect DHCP server address, please note there is no issue with connectivity, i just want to know why incorrect DHC...
Just wondering of this model of WAP - AIR-CAP3502I-X-K9—802.11a/g/ is working standalone with out a controller , or is it only controller based ? Thanks.
Hi All,Can anyone please suggest me what is the criteria for a WLC to become a RF group leader and how is a Group leader is different from rest of the WLCs in the RF group. On what basis the RF group leader is elected. Is it on the basis of Lowest MA...
Dears,Does any body have the same problem? The Samsung SCH-i569 Wi-Fi can't work at the LAP1131G with WiSM. It can associate to AP and get the ip address but about one minutes ago it had deauthentication and the phone's Wi-Fi status will show scannin...
I know you can put a minimum of 3 AIR-ANT-2422 antenna on the 1261 AP but my question is, can you mix and match antenna?Currently there is an AIR-ANT-24120 used on an older 1200 model. Upgrading to a 1261. The 24120 is 12db and 2422 is 2.4db.Environm...
