Welcome to the Cisco Community Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, September 14, 2026 through Monday, September 28, 2026. Our experts Shree Hari AB and Suman Sinha wi...
I recently discovered that the Cisco Spectrum Expert software is only displaying channels 36 to 64 on the Real Time FFT graph. I have gone over all the settings, and the UNII-3 channels are selected, but they don't show up.Does anyone know of any tr...
Hello, I am running 5508 wireless controllers. I pass along another agency's WLAN across my wireless network that is anchored to their older 4402 controller.I wish to run the new 3600 series APs and am planning on migrating to NCS and the new 7.2 cod...
Hope someone can point me in the right direction -Basically have a Win08 R2 DHCP server, and a 1941w router.I've got the internet, got the lan clients getting DHCP ok (with ip helper-address set on the 0/0 internal interface).Also have the SSID, and ...
Hello,I have a problem with connecting multiple 7925gs connecting to a single Aironet 1131. I have setup two vlans, vlan 1 and 100. Vlan 1 has about 4 devices and works like a charm, on the voice vlan, when using one phone it works fine but when I ...
We have a building near a power sub-station, so getting cable run is a problem. We do have an existing 1252 LWAP close by, but since the building in question is metal, the signal is not strong enough to use. I would like to put up an autonomous 125...
We use NOMADIX for only banner implementaion. So client gets authenticated by WLC and has to click OK on the banner. Could have used WLC for this but sometimes we need to exclude few devices that are not capable of clicking OK on banner. Would be ...
Dear all I start learning about Mobile IP( read the RFC 3344) and some related RFC documents. Now i have a concern question, Hope that you clear a canal of obstruction because it makes me getting mad.As i know about Mobile IP like this:+The Foreign ...
I have a customer running WCS on a windows server plataform (physical server), and want to move to cisco prime (UCS 210), however I can not find a migration guide in order to keep the backup, once the cisco prime will be virtualized in another server...
Hi everybody,we have a lot of WLANs and AP groups on two WiSM2. Each AP belongs to some non-default AP group. Now I would like to change default WLAN to interface mapping. But change of WLAN to interface mapping on the WLAN configuration page changes...
I have 8 no. AIR-LAP1131AG-A-K9 and WLC 2112 Wireless LAN Controller,i configured the device and its working at deffent SSIDs but when i am trying to enable same SSID on all LAP it shows "AP on dupplicate SSID found and Layer 2 security found".
Hello! Please, help me to sort my problem out.We have bought autonomous APs AIR-AP1141N-E-K9 and converted them to the lightweight mode, but they cannot join the WLC 5508. The errors are below. There were NO problems with the LAPs that were bought ...
Hi,is anyone experiencing frequent disconnection on CleanAir APs. installed 2 cleanair aps, aironet 1550 in bridge configuration. in the vicinity there co-exist ubiquiti brand APs around 3 units. i have done frequency survey and configured channeling...
Hello,we do have a site where we need to deploy AIR-LAP1142N-E-K9 and AIR-LAP1242G-E-K9 APs. We have two AIR-CT5508-K9 controllers with SW version 6.0.188.0.AIR-LAP1142N-E-K9s work okay, as expected, we do not have any problems with ...
Hello Guys,I got a project where I have to provide NATTED addresses to cutomers for the internal servers and I found out that the outside address range /27 already in use. We are using 5510 with ver 8.1. We cant use PAT here.Any other option to acomp...
Folks, I have a need to troubleshoot/test 802.11k, 802.11u, and 802.11r messaging. Does anyone know if AirPcap Nx + Wireshark will capture and properly decode these 802.11 amendments:802.11k802.11r802.11uI have looked in Wireshark forums and seen ref...
