Welcome to the Cisco Community Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, September 14, 2026 through Monday, September 28, 2026. Our experts Shree Hari AB and Suman Sinha wi...
Hi, I have a Cisco 3200 MAR. The configuration inside the 3200 MAR is [Wireless+Router]. When MAR is connected to the APs on the otherside for the first time, bvi1 is getting an IP address via DHCP and Interface between Wireless and Router (vlan 1) ...
I have always thought that a reboot of the controller was needed in order to use a new webauth bundle that you just uploaded. I am wondering if this is still true. I don't see anything about requiring a reboot in the documentation.Does anyone know ...
Dear all,I am little amatuer in networking and i am having few small doubts. Is it possible to have RF interference problem in Wimax. Because I see Wimax to be with higher frequency.
Hello,Does anyone know of a way to shut off syslog traffic for "%APF-4-ROGUE_AP_ADD_FAILED" other than by changing the WLC syslog level?We need to keep that level (warning level 4) in order to view important warnings. The message noted above is 70% ...
Hi!I like to know is there in market hotspot printers which works with Cisco Unified WLAN infra (WLC+NAC Guest Server, ACS, ISE)?For example Zyxel have this kind printer which can generate subscriber accounts and print account information with the pu...
I have setup the WLC to authenticate to a MS Server2008 NPS for a WPA2/AES SSID. The connection is successful, but client authentication fails for wrong EAP-type. I believe this indicates a Windows7 client issue. Can anyone tell me the required clien...
I have a 5508 with 4 APs connected to it.I wanted to change the global wireless channel configuration for the b/g/n networks from channel 1 to channels 3,6,11I disabled the network by going to 802.11b/g Network Status and unchecking the boxthen I cha...
I want to know if anyone has performed this upgrade. The release notes that I have looked over make it sound like if I want to do the data migration that I must first upgrade the MSE to version 7.0.201.204 and then go to 7.0.220.0. This is only wha...
I am putting in a new 5508 controller. I've built the WLANs, activated the wireless, and configured the network for DHCP.When I add a new 1262 wireless AP to the network, it gets an address from DHCP, but then says it cannot communicate with the cont...
See below config. All IP Addresses are correct and I have other AP which works. However, this one does not. They are using the same RADIUS settings.On the client machine I am getting a EAP/TTLS box asking for Domain/Username and Password (Token). If ...
Hello,I was wondering if someone out there could help me with a problem with our WLAN. We recently received our WLC 5508, AP and switches to setup our WLAN but I'm having trouble getting it all to work. It's been months since the course and I'm hav...
Hi folks!I'm trying to use chain certificate for my devices authentication. can someone please help?'couse in cisco web page I saw that it's was only possible to use chain certificate for Web Auth.
Hi Guys, I want to cover an old building where just some cables can be run, so I would use mesh, but I want to use as many APs over wire as possible.Is it possible to have wireless mesh AND non-mesh Access Points to cover the same area? Are there any...
Hello,On a 4402 wireless controller (7.0.220.0) with LAP1242AG-E-K9 and LAP1252AG-E-K9 access points I receive lots of messages like this:Dec 9 12:55:16 ap-a1 1466: AP:001a.2f58.d4d6: *Dec 9 11:55:16.174: %LINK-3-UPDOWN: Interface Dot11Radio0, chan...
Hi All,I have a (single) client (it is a cisco IOS router) behind a wireless workgroup bridge (cisco1242).The client's IP address is obtained via DHCP from the wired network.Now, when roaming occurs, the Client will never have knowledge about this ev...
