Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Any advantages to setting the AP-Manager and Management interface to an untagged vlan? Currently, our controllers have their management and ap-manager interfaces on the same untagged vlan. Would it be wise to change this? Are there any gotchyas I sho...
I've done a fair amount of outdoor wireless surveys, but they've always been for clients with existing wireless networks. Now I have my first opportunity to perform my an outdoor wireless survey where there is no existing WLAN. I have my AirMagnet,...
Hello, I'm facing a problem here and spent the weekend reading this forum. This is my first post.The facility have 25 APs on a open floor. They use Handheld computers - no notebooks - no voice.They used to have RRM enabled. After reading a lot of thr...
I followed instruction on http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a008058ed26.shtml#macbasedaclsto add a new mac address on Aironet ap1200. Unfortunately, it failed. Initially we add Mac address thru web in...
I can configure the ACS server whit Self Signed and integrate it into a Windows database?The users will be authenticate whit 802.1X configured in a WLAN in WLC4400.
Hi All,Can I use the Fa 4 (WAN) port to create several subinterface to do the vlan routing? I know 851 can't do it. Not sure about 871. Thanks.Lou
Resolved! ACS 1121 appliance configuration
Hi,I have WLC 5508 along with 3502i AP and i want to configure the ACS hardware appliance. I have worked on windows server based acs 4.1. I just want to know how different this hardware appliace configuration and installation ?what are all inputs req...
Hi,We recently upgraded our Wisms to version 6.0.196.0 and after the upgrade we have seen the clients sometimes looses connectivity and has problems to connect. We use an network with 802.1x and PeapMschapv2 with dynamic WEP.We have disabled aggresi...
Customer is trying to configure Autonmous AP's to a guest splash page with an AUP. Per this document it sounds like it is feasible.However I am not able to make it work. I have it going to the ip address of the web server. The AP can ping this dev...
Resolved! cisco aironet 1130g
hii tried to assign ip address to my access point in Lightweight mode using commandAP(config)# interface bvi 1but it doent continue give error "invalid input detected at "' markerplease help..thank you
Resolved! Wireless deployment on remote site
Hi all,I will deploy a 4400 series WLC and APs in HQ and about 10 remote sites soon. I have some requirments, the HQ and remote sites are running VPN, the WLC will be placed in HQ, the AP will run H-REAP mode and each site will have 2 SSID, one for p...
We have an existing AIR-WLC4404-100-K9 wireless controller, but is looking for another unit of controller for redundancy purpose.The AIR-CT5508-100-K9 controller is the new Cisco wireless controller.Does the CT5508 and WLC4404 perform failover betwee...
Hi there,I have a 851w with c850-advsecurityk9, I was asking me..How can I bridge my 851w to a linksys that share wireless... So I will be able to extended the network without wire.. my laptop will connect to the 851w then wil go to the internet thro...
Hello,I have been searching high and low for an answer to this question but have got nowhere!We are currently using a WLC with a WPA2 pre shared key for public internet access, we use the web authentication form to force people to enter there email a...
I want to imlement EAP-FAST with WLC and Cisco ACS. But Cisco Secure Services Client (CSSC) is not available for Windows 7 yet. Most of the client machines have Windows 7 in our case. What options are available to implement EAP-FAST with windows 7 on...
