Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, October 14, 2024 through Friday, October 28, 2024. Our colleagues Saikat Nandy, Parithosh Vema and Naveen Kumar will be waiting ...
Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, October 14, 2024 through Friday, October 28, 2024. Our colleagues Saikat Nandy, Parithosh Vema and Naveen Kumar will be waiting ...
We have a autonomous wireless setup with a WLSM and WLSE. I have an issue with where I have 2 wirless clients that need to communicate using a multicast address for an application to work.The clients can ping each other but the multicast stream is no...
Why does the WLC map the DSCP to the LWAPP's 802.1p field when the LWAP does NOT understand this field in the LWAPP data unit? In fact, the LWAP does NOT mark this field for frames going towards the WLC.Also, why does the wired switch bother with 802...
Hi all,I want to start streaming multicast video across wireless. Lucky for me, the stream isn't of too high bandwidth (100-200 kbps). However, it is multicast based so: UDP packet streaming, no ACK mechanisme.Our setup is completely WISM based.Howev...
Good afternoon,Can anyone tell if i can connect a Access Point (AIR-LAP521G-E-K9) and a Controller (AIR-WLC526-K9) to every kind of Cisco Switch (Catalyst 29XX, Catalyst 35XX, etc...) or only to Cisco Catalyst Express 500 Series.Thank you very much f...
Can ayone confirm what is the industry standard Tx power level for a test AP and when simulating AP for a WLAN survey? I think I read somwhere its 25mW and not 50mW?Thanks
Is there anyway to have or configure a Hot-Standby Root Bridge for Autonomous AP1242?My purpose of hahving this is to have a more resilience in case the Active Root Bridge is faulty on the backhaul side.In order to have more resilience backhaul for t...
Hi all,I have two AP1240 on remote office, which is connected to company headquarter by WAN. AP's were converted from standalone to lightweight mode without problem, but they now cannot join WLC, which is in company headquarter. Degug lwapp on WLC sh...
I have a 1242ag w/ ios 12.4(10b)JA. Clients drop connection and get long delays when working on wireless A or B. I have recieved errors on the ap "maxretries" is there an ios update or procedure guide I can follow to help with my problem? I have set ...
Hi, I do not know if I got this right but could someone provide a link that explains what the differences are between Autonomous AP and Lightweight on these models, and if autonomous can become lightwaight and vice versa by using different codes i...
I friends I have a Cisco ASA 5520 with an AIM Card (IPS), I have enable the IPS, but It is not working properly because I enable the skype and MSN signatures ( and I put the block inline connection, and TCP reset connection), but all the PCs can logi...
Does the controller only use the management interface to discover and control APs?In my case I created a dynamic Interface on the controller and it's in a different network than the management interface. The AP (which gets IP from a DHCP server) is i...
Hi,I will start off by saying that i only have experience with small - scale (2106 WLAN Controller)unified wireless network setup. So, i was wondering what factors do i need to take into consideration while setting up a Medium - Large scale Unified w...
Is there further information on IPICS aside from the the "Product and Services" and "Support" pages on Cisco's site? Perhaps someone who is blogging about IPICS. I am looking to further customize the platform, looks like the TUI can be scripted wit...
I have a controller model 4402 and I need to connect it to 2 Catalyst 6500 for redundance.I have connected but stp did not work well. Does somebody know if is possible do thatTks
I have a prticular requirement. I have a point to point bridge solution. Can the non root bridge act as an ordinary access point. I need wireless signal to be broadcasted from the nonroot access point for the client connectivity.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
10-16-2024 04:43 AM | ||
08-15-2024 04:04 PM | ||
07-17-2024 11:11 AM | ||
07-17-2024 06:04 AM | ||
07-08-2024 04:04 PM |
User | Count |
---|---|
15 | |
7 | |
5 | |
5 | |
4 |