Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
HiI'd like to know if i can be able to enable lag on the controller but termite it on 2 different switches? i.e. i have 2 ports on the controller, i connect 1 port on switch1 int g1/5 and connect port on switch3 port 1/10?How can i do this? as i need...
Hello,we are operating a Cisco WLAN environment with 1242 and 1131 LAP. Some of them have been converted from AP to LAP.Now we took some LAP off the wall.They are now packed in a box in our storage room.But the WCS is showing a green Alarm Status for...
Hi,I've got HREAP working well, in that when an AP loses conenctivity with the WLC the AP continues to push out a LAN over radio and clients are authenticated back onto a radius server that the AP can see when disconnected.I have one burning question...
Folks, Can I install WCS and ACS server on the same server? only for testing purposes.Thanks
My WCS reported the MSE was disconnected. Then i checked the mse status.[root@SHWIPS01 ~]# service msed startStarting MSE Platform MSE Platform is already running[root@SHWIPS01 ~]# service msed statusSTATUS:MSE Platform is up, getting the statusUnab...
Is there any way to check what power level a 7921 is using at a given moment?
My setup ist the following:APs 1242WLC 4402 25 5.2.1787921 1.3.2Loada RadioAuthetication CCKM with Local EAPThe Problem is that there is a gap in voice when I roam from one AP to another.But these problem exist only one time.When I walk the same way ...
I have configured 2 controllers with the same RF Group name in the CONTROLLERS-->GENERAL page. However, when I go to WIRELESS-->802.11A or B/G and look at RF Grouping I only see the indivdual controller I am on in the grouping. I do not see the other...
we created a dynamic interface on WLC and associated a one ssid using dhcp but this interface do not obtain IP could you help me to resolve this case on wlc?regards,
Is it possible to put an IOS (Autonomous) image on an 1142? Are they completely LWAPP?
Hi,I've configured WCS6.0 to authenticate the useres against the Cisco ACS.I've assigned all tasks from "root"-group to my user profile on the ACS, so I should have the sames rights as the local root-user. Now, when I try to view the audit-report I g...
Folks, I just setup a location sever. went through the setup tool and setup the hostname and ip address, etc.When i go to WCS and try to import the location server, it using account admin/admin and trying to connect at port 8001 to the location ...
Hi NetPro,After IOS upgrade , this AP can not Associate anymore.Previous IOS version : flash:/c1240-k9w7-mx.123-7.JA5/c1240-k9w7-mx.123-7.JA5Proposed IOS Version : c1240-k9w7-tar.124-10b.JDA3.tarAP Model : AIR-AP1242AG-E-K9Interface ...
Folks, I just installed a 2100 controller and added a WLAN. I noticed that the default L2 security policy is 802.1x which is using WEP 104 keys. My question is where do we define the wep key on the controller. does that mean no client will be a...
We have running 2 WISMs with Software 5.2.157.05 diffrent wlans are used......all wlans were working well.Now really over night, one wlan was gone away from the default group!So no ap was able to propagate the wlan anymore. The interface was ok, the ...
