Welcome to the Cisco Community Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, September 14, 2026 through Monday, September 28, 2026. Our experts Shree Hari AB and Suman Sinha wi...
I am developing the 802.11n client device (STATION) on the android platform.I confirmed that AP1252AG-K-K9 worked well in legacy mode (802.11a/g) by connecting internet or downloading data stream.But in aggregation test (ping test and internet acces...
I m using WLAN 4400 with4.1.185.0 code. I tried to create on more interface, it says "cant creat the port".However, it creates the port but does not take DHCP IP. It is also broadcasting that SSID. Any solution ?Many Thanks
I can't find an HREAP supported AP list. I am specifically looking for whether or not the 1310 in LWAPP mode can be configured for HREAP? I would also like to know where to find a list of AP's that are supported in HREAP mode.thanks
Hi,We received this question from our Facebook community.http://www.facebook.com/CiscoSupportCommunityEslam MohamedIf i have 4 WLC controller in the network , and want the AP register with wlc number 1 and secoundry one be wlc number two...i mean i...
Hi,The setup I have an issue with is one where a suboffice has a WLC. The head office has another WLC as the anchor for mobility groups. We are using a main corportate SSID with certificate authentication although the mobility group is for the guest ...
Hello,We are currently expanding our wireless deployment that consists of two Aironet 1310's bridged together. We would like to hit an area in the opposite direction that is not too far away. Would replacing the 1310 in the root point with a 1410 as ...
We are having some servere temps in Upsate NY this week. Temps ranging from -10 to -18. This morning my 1400 wireless bridge is reporting the rdaio has been disable due to a temp alarm. Does anyone know if the radio get re-enabled after the temp res...
Guys,I've ran into an issue that I haven't seen before. A client of mine has a WLC that manages AP's at several different sites on the East Coast. They are all connected via a multilinked T1x2 connection. One site in particular contains 7 AP's, an...
I was wondering if anyone would happen to know what thelow, medium, high power settings are on the AP541N in either dBm or mW?The data sheet indicates what the maximum/full power settings for 2.4 GHz are:802.11b 15 dBm802.11g 15dBm802.11n/20 MHz 12 d...
Hi folksI downloaded an authentication bundle from Cisco website, It is a .tar file. I need to edit the .tar file by doing the following:Remove Cisco Logo and put a new logo inside it.Edit the login page to fit with the deploymentImport the .tar file...
I am having trouble with a wlan at one of our locations. This problem occurs randomly with most of the users there but in the example below I have included the most troubled. The clients experience awful wireless performance and response times for ...
Hi All, i have a Setup as Follows- 5508/1142- heterogenous Client with WZC, XP, SP3, SSO- ACS 5.2, MS ADTarget is Songle Sign On wih Machine Cerificates against AD. For testing purpose we tested with EAP-PEAP/MS Chapv2 and Machine Auth, works fine. N...
Hi,I have some (standalone mode) Bridges and AP's Cisco 1310 and i noticed that when electrical power was down and then come up again these AP/Bridges didn't start up. I have to disconnect power transformer from power injector and connect them aga...
Hi everyone,As Cisco TAC engineer, I thought this medium is a good way to gather good opinions. So please leave a message saying what document you think is missing from cisco.com about Wireless products. Config examples, white papers, troubleshooting...
I'm guessing no, but not sure.
