Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 17 , 2026 through Tuesday August 31, 2026. Our experts Saikat Nandy and Prashanth Bargur Hanumantharayappa will be waiting to assist you and resol...
Hello, In our organization the Cisco wireless guest solution uses an external Juniper (sg55) firewall and it is the DHCP server. The guest users use Web authentication as the authorization piece within the WLC. My problem is users that have laptops a...
Hi,I am going o create a wireless hot-spot in a small compagny. My plan is to connect a Linksys wireless-N router to the DMZ port of the RVL200 router.It is intended that users on the wireless network should use the VPN on RVL200 to gain access to th...
Hi,In the past two weeks I have seen most of our 1020s drop off the Controller and then join again. They are sometimes down for several minutes. Each 1020 has gone down only once and then it stays up but, it seems really strange to me that they are d...
As recently new office from end-Sept, we have found that the radio interface reset very frequently which has been happening about over 15 times within 8 weeks for one AP on average. Some of those (3 AP so far) got the radio interface down eventuall...
I read in a past discussion that there might be some power issues when powering LAP 1142 having a long CAT5e cable length between the unit and the switch which uses only PoE (not PoE+). Is this true? If yes, what is the maximum cable length beyond...
hiwe are experiencing problems with Cisco AP 1000 series after we upgraded IOS on WLC 4400 series to 4.2.209.Problem:In WebUI Ap detail page, ap group name is shown as '--' . and no SSID is attached on APs after upgrade.when we are looking in WCS (6....
Hi, All I have a question that I hope someone has done before. I recently installed a new WCS as our existing one is full at 3500. Does anyone know how to migrate the lightweight Ap templates from one WCS to another? Kind Regards, Carl
Cisco that product to replace VigSys VR20? I want to find a cisco products to replace VigSys VR20 products, we must ensure that the corresponding parameters are compatible. So the cisco this product specific models is what? VigSys VR20 para...
Hi, how to download IOS-images for upgrading and downgrading 1242-AP from/to autonomous mode?
Hi,Can anyone tell me what type of connector is on the AIR-CAB005LL-N (male or female)?In the list of N antennas some come with male connectors and some with female.Thanks,Justin
Can i have a management ip and native vlan in different subnet on a AIR-1242 and 2960 switch?Native on Switch = 1.Interface vlan 100 = 10.10.1.25X /24BVI ip in vlan 100 = 10.10.1.25X /24-HM-
A couple of years ago a broken ap was removed from our network. Something went wrong in the handling an we still recieve alarm messages stating "AP 'xyz' disassociated from Controller". It can also be seen in the "Add Access Points" list.What can we ...
Hey,I have a Air-AP1141N-A-K9 and I want to set it up as a repeater bridge. I have the web interface up already. I was wondering how to set it up as a repeater for my primary router. I think it only supports 2.4 GhzThe IP for my primary router is192....
Hi,I have whole cisco wireless setup. I have Cisco 1242 AG access points. I am trying to connect my Lenovo laptop which is having Realtek lan drivers but whenever i connects to the wireless it gets disconnected on regular basis. plz helpRegards,Pras...
I've hit uppon a problem and I think its due to a change in the code between 6.0.x and 7.0.x versions of code.We've got a large campus which is a mixture of hospital buildings and university buildings, the university buildings have a separate wireles...
