Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Hello,We have deployed LAP 1242 APs with one antenna connected to the right hand side antenna connector and the left one is not terminated. The APs are separated 2 inches vertically and 7 inches horizontally. The controllers are configure for auto p...
Resolved! Guest WLAN
Hi,i m in trouble to configure guest WLAN in WLC 4402.i have created 2 WLAN and 1 GUEST LAN and configured correctly.but i m not getting SSID advertisement for GUEST LAN in wireless network when i search available SSIDs.i have mapped GUEST LAN with t...
After we upgrade to WiSM 4.1.185.0 for 5 days, we got critical alert message about "CPU Receive Multicast Queue is full on Controller" from one controller. We have never seen this error in previous versions. I do not see high CPU usage ...
Hi All, I would like to enable HTTPS access for my access points. It can be done with ip http secure-server. Along with the same I would like to enable accounting for the https access. Is there any way for the sameThanksNikhiL
I'm running a WLC 4002 (ver 4.2) remotlyI can ping the service port ip - but cannot telnet/ssh to it.Does these services would have been enabled before?
Hello We're having a problem with web-authentication on our 4404/WisM controllers since we moved to software rev 5.x (currently running 5.1.151.0). With software rev 4.x our web-auth SSIDs would send the authentication requests to a Cisco ACS4.0 whic...
I have a very small branch office, with a single cisco AIR-AP1231G-A-K9 running IOS 12.3.8 JA. I would like to have them authticate using WPA-PSK and lock them down by mac-address without getting *eap/RADIUS involved. I have it configured however whe...
Resolved! WLC vs WCS version
Hi guys,can i use version 5.2.178 on my controller and 4.2.110 on my wcs?Better:have WLC and WCS to run the same main version (4.2 and 4.2,5.2 and 5.2) or are the wlc and wcs version not related?(5.2 and 4.2)thx...
I have a AIR-AP1230B-E-K9 access point, which worked fine in its original hardware configuration, which included an AIR-MP20B mini-PCI radio module (802.11b standard).I decided I wanted to upgrade it to be a dual wireless, 2.4Ghz and 5Ghz access poin...
Dear All,Currently I have wcs 4.1.9 licensed for 50 AP's with a pair of wlc 4402-50s.I expect to ramp up to about 50 AP's over the next six months.I plan to build a rhel4es server to host the wcs. I can find only very sparsedocumentation describing t...
Hello AllMy working AP1200 crashed in the bottom I am seeing the lights for radioand ethernet red and status is light purple on the other hand in console mode I am just seeing ap:and possible commands are ? -- Present list of available comm...
We are trying to add a disclaimer page for public users to accept and continue for our public WLAN. Need to know how to add this page, and if there is a character liimit?
I have a controller that sometimes does and sometimes doesn't prompt for memory test at boot up. What triggers the prompt for memory test at boot up?
I am trying to Power a Cisco 521 AP from a blade on a 4500 switch. The blade module number is WS-X4548-GB-RJ45V. This is supposed to be a POE blade, but when I plug the AP in, I do not get the AP to power up.
I was running version 4.2.130 on 3 wism blades. Actually one of the controllers in one wism is running a mesh code, so i did not upgrade it. Upgraded all except one (cause it won't upgrade, thats another battle) to 4.2.176.0. And now the controllers...
