Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Can anyone explain what the difference is between admin status and oper status within the WCS GUI. It appears that disbaling either on effectively disables the radio...is that correct?
Hi everyone, I am a rookie at computers. I have 'cisco systems 350 series pci wireless lan adapter' and it does not work because under device status it says "This device cannot start (code 10)" I've uninstalled it and re-installed, updated the driv...
Resolved! Set AP as client
Hi to all,Can I set an AP (1200 o 1300 series) as client?My problem is that I have to connect a video network camera to a WLAN but I cannot configure it as bridge. So I ask can I associate a AP as client to WLAN and then connect to eth of AP the netc...
I recently have added a second Vlan on my access point. However, it's not getting an ip.I am VERY new to the whole Vlan stuff and to more advanced networking so i am not sure what is wrong. I am thinking maybe it is because the AP is sitting behind...
Hi!I have a 870-router running 12.4(9)T2.my setup consists of a bunch of PC's connected using a 3com wireless bridge and one wireless laptop. The 870 is also acting firewall, so it has an internet connection in fa4.All devices can reach the router an...
Is anyone else having problems with WISM based controllers unexpected crashing? I have an open tac case and I did get a replacement module for one switch, but I am not confident that the problem will go away. The system is not logging anything to ...
Dear,I'm in the need of temporary replacing a 2006 controller with a 4404 controller. I have all the 2006 templates in wcs. Can i expect big problems when pushing these templates to the 4404 ?
Hi, have anyone encountered during power up of Cisco Aironet 1410 (with integrated antenna), the Install LED status is solid amber all the time? At Bridge LEDsInstall LED - solid amber3 LEDS - noneAt power injectorUplink - OffInjector - Blinking Gree...
This is the scenario; Before I upgraded Windows XP to Service Pack 3, the Cisco Spectrum Expert worked fine. Once I upgraded to Service Pack 3, it doesn't work anymore. The program starts, but it is not detecting any RF signals. When I check to see i...
CISCO 4404 ALERTS TO BE GENERATED(mail has to be triggerred) WHEN WLAN CLIENT AUTHENTICATION FAILS.Is there are any options on WCS to enable Authentication Failure on WCS.I have already Enabled 1.Client authentication failure Alarm and Authentication...
Hi, a I have this question:To run the Cisco Spectrum Expert Wi-Fi is necesary a WCS running in the Wireless Network ? I have a Wireless LAN, with Autonomous Access Points and would like run Cisco Spectrum Expert Wi-Fi to monitor my WiFi Network.
Are there any known issues by installing an antivirus software or upgrading to (microsoft) service pack 2 or 3 ?
Resolved! Access Point Question
I have a Cisco AIR-AP1131AG-A-K9 wireless access point. This AP is an autonomous (stand alone) AP not used with a wireless controller. I used Cisco's upgrade tool & the correct image to upgrade the AP to LWAPP (so it could be used with a Cisco wirele...
Hi Experts: Please help me on this-How we can proof bandwidth utilization/throughput over outdor point 2 point connection, my customer wants 20MBPs throughput, plz suggest me do we have some software or some other way to proof it?
Hi, I am configuring a Nokia E66 (wich is v4 in Cisco Compatible Extensions, so it supports EAP-TLS) with WPA2 EAP-TLS against IAS in a Cisco Wireless Network and I always obtain the same error in the IAS event viewer.denied accesssAuthentication-Typ...
