Welcome to the Cisco Community Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, September 14, 2026 through Monday, September 28, 2026. Our experts Shree Hari AB and Suman Sinha wi...
AP1231G-E-K9 was converted to a thin client AP to be managed on a controller.After a 'succesfull' conversion, the AP did registered with the controller, but since it's located at a remote site, it was be be coverted run HREAP. The AP is connected on ...
Could we use an 1140 or a 1230 to bridge or relay (no network drop) to an existing WLC system?
Hello,Is there a way to stop RIM (Blackberries) and iPhones, Nokia's and Sony from connecting to the guest network as they hog IP addresses? I would like to do some "range" mac filtering or sommat, but only for iphones, and rim, and mobile devices, b...
Hi all. I am hoping someone can assist me with this.I have 10 APs (all 1242s) and a WDS (also running on a 1240 Aironet). All of the APs authenticate to the WDS successfully. The WDS uses it's own local RADIUS server for authentication and there is a...
hi what is the steps to configure EAP FAST from ACS V5 and in DEL and HP wirless clientsin additional CAN ACSv5 support EAP TLS?Regards
I have a 871W I am going to use for a conferance in hotel. There will be 30-35 users. Not all will be wirelss but most of them will. How may clients can a 871W support? I also have a 1242 Aironet. Would I be better using that?
We use AP1230's as AP's and as workgroup bridges (WGB's) so we have Cisco on both ends of the RF link. We'd like to control the amount of upstream bandwidth from wireless clients while leaving the download side unrestricted.IOS on routers supports th...
HiI've just upgraded WCS from 4.2.128.0 to 6.0.132.0 But WCS won't start. The hm_launchout.txt file show:Starting Health Monitor as a primaryChecking for port 8082 availability… okStarting Health Monitor Web Server…Health Monitor Web Server Start...
"1252 both radios installed w/one radio enabled @ full N speed on 802.2af power"Are there any special instructions to make this work as described in the documentation for the latest SW Version 12.4(21a)JA1?"Support for 802.11n Performance on 1250 Ser...
I installed a Cisco Aironet 1200 access point for use with a few Macs, some old Dell D600 and iPhones. I have enabled both G and A netorks (tried various channels as well) and cannot get the old Dell D600 and/or iPhones (3G and 3GS) to see the networ...
Hi,I have some Zebra printer with static IP Address, they are unable to connect to the WLAN, but if I enable DHCP required, the connect. In the WLAN configuration, I'm permiting static IP Address asignment.Any ideas?
Hi,I am Cisco WiSM consists of two Cisco 4404 controllers which is installed on the 6503 Switch. I am using Mac Address based authentication for clients to get connect.When i am adding a new client's mac address to one controller, it is not reflectin...
In a standard WGB configuration with a controller, can connect to the switch besides the AP WGB too another AP to allow wireless customers? That is, to have a wireless client connects with a AP in the WGB switch. View image
We are currently running version 4.2.62.0 on WCS and we are looking to upgrade. I've been searching for the proper upgrade path for this. I would like to go to 6.0 code. All the controllers will be upgraded to 5.2.178 once WCS has been upgraded. Plea...
Hi all,I cant seem to find the solution. The last act of our previous network admin was to reset the passwords on the access points before he left. Now we cant log in. I tried the mode button on power on, but the Cisco/Cisco login does not work. The ...
