Welcome to the Cisco Community Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, September 14, 2026 through Monday, September 28, 2026. Our experts Shree Hari AB and Suman Sinha wi...
I am intending to manually reset the LWAPP (1131), however, is there a way to access the LWAPP CLI? Currently, the LWAPP is stuck in a loop, thus debug message on the LAP display " No Join Response from WLC". So, because of this recurring loop, the...
WLC (4402 and 2112) running version 6.0.188 is displaying the following error in the msglog.“*Dec 11 15:13:12.185: %USMDB-3-MSGTAG030: usmdb_apf.c:262 For information regarding Emergency image Version,Please refer Controller documents”The solution to...
I am trying to set up the above hardware to take advantage of the wireless network in my warehouse. What I am looking for is Incoming PSTN calls go to the WIP310 and when I want to make a call from the WIP310, it goes to the PSTN port of the SPA3102...
Hello,can one controller 2100 be used to manage APs in the headquarter and in branches?We plan to use 6 APs-1131 in the HQ and 4 APs-1131 in the branch. Is this scenario supported by a AIR-WLC2112-K9 in the HQ?What do I have to check regarding the WA...
Hello,I have to set up a wireless network using 802.11n. I was wondering if the 4.2 version is the best one? Is there any document that tells wich version to use depending on the the configuration we need to set up, for example?jr94
Hi alli have a problem with the voice calls when roaming between aps (1130). my controllers are on version 4.2.61.0. is there something i can do on the configuration side to fix this? the phone just goes quite (silent) but the call doesnt get dropped...
HiMight be a strange one.We've got a medical deivce for Breast Care, a Solaris System, which doesn't have a wireless card,, or so the Solaris engineer says. but for some reason it trys to authenticate using CAPWAP. far as I remember CAPWAP is from t...
Does the WCS now support the Autonomous AP or does the Autonomous AP need to be converted to LAP in order for the WCS management?
We have a new deployment with a Cisco 4402 and 1131 AP's. The phones are 7921's and the network consists of a 3560 (network routing device), and 2960's as the access devices. The wireless phones are on their own VLAN as are the wired phones. We are u...
Hi allI got a couple of accesspoint AP1231G with a MAC-Filter configured.Now I'm curios if the access-list has a maximal mac-address limitation.At the moment there are about 130 MAC-address and couple of clients have sometimes trouble to get connecte...
Hi,We currently have an Wireless infrastructure setup in our warehouse with 3 Aironet 1250 series Access Points. We have Motorola MC9090 devices connecting the Access Points. The whole warehouse is not even 2000 sq ft in area. But we notice the norma...
HelloWhere are the entered email-addresses logged in the Web Passthrough authentication mode? Is it possible to send this inputs to a syslog server?regardsPascal
CSC,I have a question on the lightning arrestors for 3G antennas. I think I may have found a typing error in the technical data. We have purchased a 3G-ANTM-OUT-COMBO which comes with a 3G-ANTM-OUT-OM outdoor omni-directional antenna and a lightning ...
40 locations, around 20-30 APs per location, 1 gig back from each site to the main site, minimizing cost. Client wants support of remote site survivability and reducing network loading. This implies H-REAP. We can't put controllers at each location d...
Hi,There is no L3 network connection to some of the 1522 APs in our mesh network.They register with the 4402 WLC (5.2.157.0)i.e. appear in the AP list. When sending ping packet to APs IP addresses from WLC or PC there is no response, but I can see AP...
