Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 17 , 2026 through Tuesday August 31, 2026. Our experts Saikat Nandy and Prashanth Bargur Hanumantharayappa will be waiting to assist you and resol...
I am experiencing several seconds of loss of speech during a roam with the 7921. Any thoughts?WLC - 4.2.1301250 and 1240 AP's7921 v1.2.1Auth - EAP-FAST with CCKMEncryp - TKIPWhen I debug client mac for the phone I get the following error:Tue Apr 14 1...
After I reset the controller to factory defaults and go through the CLI config wizard, the mgmt ports (no matter which one i assign) do not work. I can not ge to the GUI after if i do a config network webmode enable. I can see the IP address through ...
Hi Friends,I was wondering if Site-specific Vlan's can be implemented on Guest-vlans where SSId's are anchored to Anchor-controllers from main controllers.I will appreciate any inputs.ThanksJAy
I have 2 AP's that I seem to be having somekind of issue with. I can be associated to one AP and as I move close to the other, I never change association. I can be stand 5 feet from this AP and still not associate to it. If I disable and re-enable my...
Hi!I have a particular installation on a customer site.The management vlan is the number 1 (which is the native vlan) for the whole network and all the switches tag the native vlan.So when I plug my AP on a port of a switch configured in trunk mode, ...
I have a 3750 wireless controller with 24 Ethernet ports on the front.How do I configure those ports (vlan etc) - if I connect to the console port on the box I can configure the wireless controller but I dont see how to can access to the switch so I ...
Hi, Probably a silly question but was wondering why it is not possible to convert an autonomous AP to LWAPP by using CLI commands?For example we have over 300 access points to convert and thought about using Linux to automate the task but seems there...
Last week we upgraded the WiSM controllers from version 4.2.207 to 6.0.182 Since then, one of the controllers' CPU stays at 95%. Yesterday I reloaded the controller and after a couple of hours it went back to using 95% CPU. On this state, it is not p...
hi experts,i would like to know how to verify using show commands in CLI if 1131AG AP radio is working and if clients are associating on AP
Even though telnet appears to be disabled on the WLC, it is still allowing me to telnet to it.WS-SVC-WISM-1-K9Product Version............. 6.0.182.0Web Mode......................... DisableSecure Web Mode................... EnableSecure Web Mode Ciph...
Hello: I have several AP 1300 outdoor, working fine, since two days ago, one of them, lost communication with to Rooot Bridge, the interface Dot11Radio0 stay in status RESET, I don't know why.My IOS version is 12.3(8)JEA2. I enter in the Interface pu...
Hi,Is it possible to make next design -->*WLC*--LAN--*LAP1* --WLAN-- *WGB*--LAN--*LAP2*So, is there any limitations, will LAP2 reach the WLC?Thanks,Teemu
I consider myself to have a pretty good feel for configuring VLANs and IP addressing using Cisco routers and switches with the CLI. Today I was trying to setup an 1100 AP for data and voice VLANs using the web interface and found it incredibly confus...
I have 2 WLC4402-50 connected to an Extreme Black Diamond chassis, using GLC-T. I have configured LAG on the controllers to support the number of AP's needed and I have configured the ports on the switch to use LaCP aggregation because that is what i...
Dear all, I am facing the problem with WLC 4402 . I am using thirty 1141n AP with WLC 4402. In some Access point , it is showing LOAD Profile failed as the the number of client connection exceed 12.I need min 25 client to be be connected to the acces...
