Wireless

Hi,Can anyone explain to me the difference between ad-hoc and mesh.I read in some places that mesh follows 802.11s which uses the mac80211 stack which is present in the 2.6 kernels.when we are creating a mesh network, the VAP would be in the ad-hoc m...

Hi all,I have some 7921G phones on loan to test out. But i'm struggling to get them to connect to our Aironet1200 AP infrastructure. The phone just keeps "Locating Network Services" then evetually states "Connection failed"We use PEAP on the APs with...

Dear Friends, I do have 7921[CP-7921-E-K9] ,which needs to connect to 1252 AP [1252LAP-E-K9] .controllers used is WiSM [5.0] Initially country code configured was AE and later was added US .When I try to connect to the AP , it displays on the phone ,...

Is there a way to determine which AP you're connected to?I don't have a WLC, but have several access points in infrastructure mode. Of course, all of the APs have the same SSID. Is there a way to figure out exactly which one I'm connected to at the t...

hai friendsi bought one cisco ap 1240g.but while i am typing to conf ter in enabled mode invalid command.and i put sh runit showing only one fastethernet interface and there is no bvi interface on that.and full it is showing related to the certificat...

Can the 1252 be used in 802.11n mode with the 5 GHz 5170 diversity patch antenna? I only need to light up a section of my office (two intervening walls) and the 3 omni dipoles I am now using are marginal. Will the absence of the 3 antenna connection ...

Hi,I have a Cisco 877w, can I lock it down so only my wireless laptops (only 2) are allowed on via the wireless. Is there a way to lock it down by mac address?Thanks

Has anyone successfully set up multiple anchors for guest access for resilience?I have my 2 anchor controllers in the DMZ, and on my local controller I set up both as the anchor point for the guest wlan.Only the first anchor gets traffic - the 2nd ne...

I need information about setting up an Aironet AP 1240. It seems that the configuration at RF setting does not seem to be at its peak. We use only the protocols 802.11 b\g and the speed is at 54 Mbps. My question is, what configuration should be used...

I would like to know what is the scope of the AP 1242 in meters??

I have an existing network with Non H-REAP AP's and I am installing a remote office using H-REAP APs. I am using some of the same SSIDs on both sites and have enabled the H-REAP setting on the WLANs.The design guide I looked at had this note;Note: Ac...

Hi,Has anybody configure secure mobility groups on 4402/4404. I put mobility secure-mode enable command on both controllers. Mobility Protocol Port status has change to 16667 (after reboot) but I have Data Path Down. Do I have to configure something ...

I have 2 SSID in my wireless network. 1 for the cooperate users and 1 for the guest. The guest SSID is broadcast and when a user open an IE, they will get a screen for user name and password. My cooperate users are using AD and integrated with ACS 4....

Hi,I have a metwork with 35 AP 1242 (only 2.4ghz band) and 30 7921g.I'm using a WLC 4404 version 4.2.61 7921G version 1.1.1, CCME version 4.1, AP IOS 123-7JX.The coverage seems to be good and also the overlap.The problem is: some times casually and a...

I am running device troubleshooting in cisco works on a 1200 series acces point. I am getting the followinf error message: VTP Disconnected Domain DomainName:NO_VTP Do I need to upgrade IOS on all AP's??