Wireless

Ive got a WLSE and a bunch of APs, Can I push out a command from the WLSE to update all the APs so that they are prepared to support DST this weekend? Or do I have to do this manually for every AP?

LAP,power-supply is AIR-PWRINJ3error message is output in wlc,how can i resolve this ???thanksLog System Time Trap 0 Wed Aug 13 23:40:58 2008 AP's Interface:1(802.11a) Operation State Down: Base Radio MAC:00:1f:26:2a:b1:f0 Cause=Radio Low Power 1 Wed...

Hi,I received an AP1131 from my custoemer who said it just quit working. I checked the configuration in CLI and Graphic Interface where I found a message in "interfaces" that showed Ethernet but radios 0 y 1 said not installed. I reload the version b...

Hi guys,i have a 2106 WLC with three 1131AP LWAPP.I should cover a zone where there is no network cabling and i was thinking about another 1131 in mesh mode.Do I need particular software release?Can anyone provide documentation from which i can start...

Hi guys,I have a 2106 with a non mesh release and four 1131.I need two oh these 1131 work as RAP and MAP so i i understood well the steps required are:1)Donwload a mesh release2)Once Ap are controlled change their operative modeDo I miss something?Th...

I am configuring some AIR-LAP1242AG AP's with a variety of external antennae. I notice within the WLC the antenna gain should be value which is then "x 0.5 dBm". My question is for an AIR-ANT4941 antenna, which is a 2.2 dBi Dipole 2.4 GHz, what shoul...

Cisco have been kind enough to lend us a 4404 WLC and I've got to grips with setting up our WLANS on it and I can get an AP to pick up config from anywhere in our extended network.I am, however having a problem trying to get an access point to join t...

I have trouble capturing lwapp data frames. I have AP on port 1, i have instructed my switch (3750) to monitor this port and send it to a available port on the same switch (no stacking). On the second port , i connect my sniffer. I see lwapp control ...

I have network of 7 AP's all of them 1240 series running with full IOS. I have configured one AP as WDS and the same AP is configured as local Radius server for WDS. All the AP's get registered with WDS and clients also get connected but just after m...

Hi,At one of our sites we regularly have problems that the access-points can't connect to the radius server in the central site. My collegue configured the aaa dead-time but this gave no difference.This is the error message :10:02:14 bstonw53 RADIUS-...

Maybe a stupid question but what is the USB-port on the 7921 desktop charger for? I mean it would be nice to be able to use various kind of functions, other than charging the battery, when connecting it to a PC.

Hi All,The problem is we have lost the href configurtion after upgrading an ap from 4.2 to 5.1 release(i.e AP was on WLC 3 running 4.2 relese and i have moved it to wlc 2 running 5.1). Can anyone know whats the reason behind this.

I have to install a new wireless network. I have two controllers 4402, an WCS and Cisco Location Appliance (will also use RFID). Which versions was recommend for each one? Is there a compatibility matrix between the location servers, the WCS and Cont...

Does any one know if it is possible to have a 2811 with both a WLC integrated with SRST. I know the 2800 have bundles where you can get one or the other but is it possible to have both in the same router?

I need some advice on setting up what is probably a very unique wireless network. My client wants me to set up a wireless network for their guests in a bed and breakfast which happens to be a castle. It is very pricey to stay there so the wireless wi...