Greetings, ive configured the 4400 controllers before and am familiar with the terms involved, ive recently acquired a 2106 controller, i have assigned an AP Manager and Management Address to Port 1 on the same subnet and can ping the device.Subseque...
I have the following scenario:WLC01 on 172.16.72.200AP on 172.16.72.4 (DHCP)WLC02 on 172.16.32.200 (different subnet)I have DHCP servers on each subnet, and routing between them is operational.The two WLCs are on the same mobility group and they can ...
Hi - Can somebody tell me the best way to enable and configure the wireless capabilities on a c3825 ? It already has a HWIC AP card and i can see the dot11radio interfaces as admin down. My client already has a seperate LinkSys system and wants to mi...
I have taking over this gear from previous admin. we want to upgrade versions to the latest.we have: Cisco 4402 ver.4.0.179.11 50 ap supportCisco 2700 ver.2.0.31.0WCS ver.3.2.40.0I have installed WCS ver. 4.1.83.0 and restored that old DB on new serv...
Hello,Please help I have read every doc on this AP and this antenna. there are three jacks on the radio labeled a - b and c. There are three cables on the antenna. which cable corresponds to the correct radio antenna label. Or does it not matter. Loo...
We are about to upgrade ACS from 3.2 to 4.1 and I understand the format of the PAC changes in ACS 4.x. Is this the chase, and will all users need to be provisioned with a new PAC?
Please let me know if my config is valid. Sorry i don't have visio's but from what you see, syntex , etc..does it look ok? do you see any problems with this. attached is the complete config for the ASAWeb Site Piece (External)access-list acl_inside p...
What am I doing wrong? I have configured a blank 857w with the config described here:http://www.cisco.com/en/US/docs/routers/access/800/850/software/configuration/guide/wireless.htmlHowever I get an error when I no shut the Dot11Radio0 interface conf...
I am trying to update our Smartnet for our location appliance but can't get the serial number. It's supposedly printed on the bottom of the device or accessible via WCS 'Advanced Parameters' page. The appliance is mounted in a rack not easily moved a...
Having issues with a cisco 2950 switch that is feeding off of a lwapp 1242. The 1242 is connected through mesh to a 1510, I can connect to the 1242 throgh wireless and it works fine. I plug the switch or even plug the laptop directly into the 1242 an...
I have a Wireless Controller 4402 connected to one sw2960G.I configured the controller with LAG and the switch (sw2960G) with etherchanel.I connected the controller 2 distribution ports to the 2 ports of the switch (configured with etherchanel).It wo...
I have a set of bridges working right now on 1 vlan..which is the mgmt vlan I believe. What I need to do is add 4 more vlans plus a management vlan to this link for student registration(reg,quarentene,no -access and fullaccess vlans). The SSID I have...
I am looking for a Linksys Access Point which supports follwoing features802.11 a/gSNMP support Vlan SupportYour promt reply is highly appreciatedcheers
Hi Guys,This is a little bit of an odd request however I need to allow a sync routing due to some legacy routing to pass through my ASA.I have allowed IP any any between the particular hosts involved to allow for high ports etc.. However the ASA is t...
I am trying to get a AIR-LAP1252AG-A-K9 to associate to the 4402 with no luck. It shows up in CDP neighbor but not as an available AP. Please assist!
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 10-15-2026 05:58 PM | ||
| 10-12-2026 06:46 PM | ||
| 09-30-2026 07:34 AM | ||
| 08-10-2026 11:32 AM | ||
| 08-06-2026 09:29 PM |
| User | Count |
|---|---|
| 3 | |
| 2 | |
| 2 | |
| 2 | |
| 1 |
